PDA

View Full Version : MgCamd 1.35a for AzBox HD



MickeySa
20-01-2010, 10:33 PM
Added support for CCcam .

tsakman
20-01-2010, 10:39 PM
And support for via 2.6

And here is the keys for via2.6 for mgcamd

http://www.mediafire.com/?twhlnimtu4l

Smudger
20-01-2010, 11:14 PM
Am I missing somthing where do we get 1.35a from? I've found 1.35 but not 1.35a.

fredda88
20-01-2010, 11:30 PM
Try here! (http://www.mediafire.com/?yxzutxodnnm)

CU
20-01-2010, 11:43 PM
yes, work fine (BIS, JSC+ , SCT ) :respect-055:

Mgcamd 1.35
download directly Azbox from techsat camd server
http://techsat.info/AZCamd

medmed
21-01-2010, 12:17 AM
the cccam client it s work very nice and stable ; good job team
note change mg_cfg for your config

kleinerjunge
21-01-2010, 12:46 AM
Is this version working on Azbox HD? If yes, also as CCcam Client? Better than MlutiCAS' CCcam client??

cu
KJ

colla
21-01-2010, 12:49 AM
You should have a look at myazbox ;)

yes its running fine on azbox
in my opinion on orf better that multicas

but i have problems with polsat

irishchris
21-01-2010, 01:12 AM
hi guys installed this directly from server. deactivated multicas and dvabi and placed mgcamd as top priority. however does not appear to be working and when i check ip:16001 nothing appears?

am i missing something?

goran
21-01-2010, 01:16 AM
Working VERY well... ;) Very good job, very cool!!! :)

Now, can we have Mbox added, too, please... :D

Oh, Kanber, m8: can we have a nice mgcamd.info plugin, please... :respect-054:

==============================

Try the file attached to this message...

This is what I did:

-added the Via 2.6 keys to SoftCam.Key,
-added AutoRoll.Key,
-edited the mgcamd_cfg [G line to 41 = 01 Newcamd + 08 GBox + 32 CCcamd].

Then, one must:

-rename peer.cfg.example and cccamd.list.example to
peer.cfg and cccamd.list,
-edit peer.cfg and cccamd.list.

peer.cfg:

M: { my.dyndns.org { mypass}}
#
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}


cccamd.list:

C: peer.DynDNS.something port username password


Then, send them to mgcamd folder in your AZbox HD via FTP.

Give CHMOD to 755 -> mgcamd and AutoRoll.Key.

This is just to be a client.

Dunno if what I did was 100% correct but it works. Tested! :respect-048:

=====================

If you have an original card and you want to combine MGcamd with NewCS card reader/server you will have to edit it some more...

Search this forum for info...

Good luck! :respect-048:

irishchris
21-01-2010, 01:26 AM
hi guys sorry to be a pain. but i have installed mgcamd. set c and flines in mg_cfg. deactivated all other cams and put mgcam main priority. what am i missing ? chmod perhaps?

FME_fta
21-01-2010, 01:42 AM
MGcamd is only a client of CCcam (up to 2.1.1), so no F lines.
Only C lines in cccamd.list

MickeySa
21-01-2010, 02:02 AM
Works fine even with the 2.1.2 and 2.1.3 , i

FME_fta
21-01-2010, 03:37 AM
I didn't tested MGcamd with cccam, but some say it just works up to 2.1.1
It's good to know it works with more recent CCcam versions.

leerock
21-01-2010, 08:31 AM
Works fine even with the 2.1.2 and 2.1.3 , i

Are you sure m8, coz here it doesn t request ecm from 2.1.3

goran
21-01-2010, 09:59 AM
It's a bit slow to open channels but it works nicely... As in stable and well!:respect-048::respect-applause-00

Carp95
21-01-2010, 10:03 AM
@Goran

Did you set priority.list?
Also did you set de P line in mg.cfg?

Standard it's Gbox, newcamd,CCcam

P: { 00 }

CCcam, Newcamd, Radegast, Gbox

P: { 02 }

goran
21-01-2010, 10:09 AM
Thanx for drawing my attention to it.

No, I haven't touched it, as it just worked...

So, maybe I will try prioritising CCcam now and see... ;)

rmt
21-01-2010, 10:11 AM
In my opinion, mgcamd is the most stable one at the moment

It is great news that mgcamd also supports now cccam client mode

Carp95
21-01-2010, 10:21 AM
Thanx for drawing my attention to it.

No, I haven't touched it, as it just worked...

So, maybe I will try prioritising CCcam now and see... ;)

Then there's another option:




# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 41 }


Only CCcam:

G: { 32 }

CCcam + Newcamd

G: { 33 }

Friendly-Face
21-01-2010, 10:30 AM
i can confirm that it works even with CCcam 2.1.3 do not know how is possible, but i have an Qbox One runing CCcam 2.1.3 and then i connected my Azbox last night just to test this and yes MGCAMD works like charm LOCALY with connection to my QBOX ONE with CCcam 2.1.3
CCcam and newcs mod

Carp95
21-01-2010, 10:38 AM
priority.list ( change to your needs):


# use this caid
S: { 00 2F }
S: { 00 30 }
S: { 00 68 }
S: { 00 6A }
S: { 00 6B }
S: { 00 6C }
S: { 00 6D }
S: { 00 80 }
S: { 00 81 }
S: { 00 82 }
S: { 00 86 }
S: { 33 11 }
S: { 41 06 }
# use this caid
X: { 06 02 }
X: { 06 03 }
X: { 06 04 }
X: { 09 1F }
X: { 09 2B }
X: { 09 3B }
X: { 09 63 }
X: { 17 02 }
X: { 0D 00 }
X: { 0D 06 }
# TNK, FocusSat, C+ Nordic
X: { 0B 00 }
# use this caid
N: { 18 01 }
N: { 18 03 }
N: { 18 10 }
V: { 00 74 00 }
V: { 00 78 00 }
V: { 01 50 00 }
V: { 02 00 10 }
V: { 02 08 20 }
V: { 02 08 10 }
V: { 02 11 00 }
V: { 02 11 10 }
V: { 02 15 00 }
V: { 02 17 00 }
V: { 02 38 00 }
V: { 02 3B 00 }
V: { 02 44 00 }
V: { 02 51 00 }
V: { 02 0A 00 }
V: { 03 07 00 }
V: { 03 20 00 }
V: { 03 20 10 }


ignore.list ( change to your needs )


# CDS Irdeto2
X: { 06 22 }
#Sly old ident
X: { 09 61 }
# Sly old ident
X: { 09 19 }
# Cyfra+ Seca2
S: { 00 65 }
#Can***** Pro
S: { 33 17 }
# Cable Operators
V: { 03 2A 00 }
V: { 03 2A 10 }

crazy2
21-01-2010, 10:49 AM
mg.cfg

G ( 41 ) cccam+newcamd+gbox ok

Carp95
21-01-2010, 10:53 AM
mg.cfg

G ( 41 ) cccam+newcamd+gbox ok

If you use those 3 thats the correct setting, if you only use CCcam then:

G: { 32 }

I always prefer settings to my needs

Smudger
21-01-2010, 11:38 AM
I'm getting there but not getting ecm's through yet I get.

lines of
[cccamd] Card remove from 192.xxx.x.xxx:12000 (00000this number changes )

I've set everything to carps settings any channel best to try on first?


Anyone please.

goran
21-01-2010, 12:00 PM
Sometimes you need to be patient until it gets [remove? or extract?] data from a card...??? Might be a linguistic "misunderstanding"...

I changed a channel and this is what you get:


[mg0] stoping camd..
[mg0] stopped
[mg0] service 746F index 0 pmt pid 0 (2)
EMM: CaID: 0x0100 -> CaPID: 0x00C1 ProvID: 000000
EMM: CaID: 0x0100 -> CaPID: 0x00C4 ProvID: 004106
*EMM: CaID: 0x1810 -> CaPID: 0x009B ProvID: 000000
*EMM: CaID: 0x1870 -> CaPID: 0x07DF ProvID: 000000
*EMM: CaID: 0x1871 -> CaPID: 0x07E0 ProvID: 000000
*EMM: CaID: 0x1872 -> CaPID: 0x07E1 ProvID: 000000
*EMM: CaID: 0x1873 -> CaPID: 0x07E2 ProvID: 000000
*EMM: CaID: 0x1874 -> CaPID: 0x07E3 ProvID: 000000
*EMM: CaID: 0x1875 -> CaPID: 0x07E4 ProvID: 000000
*EMM: CaID: 0x1876 -> CaPID: 0x07E5 ProvID: 000000
*EMM: CaID: 0x1877 -> CaPID: 0x07E6 ProvID: 000000
*EMM: CaID: 0x1878 -> CaPID: 0x07E7 ProvID: 000000
*EMM: CaID: 0x1879 -> CaPID: 0x07E8 ProvID: 000000
*EMM: CaID: 0x187A -> CaPID: 0x07E9 ProvID: 000000
*EMM: CaID: 0x187B -> CaPID: 0x07EA ProvID: 000000
*EMM: CaID: 0x187C -> CaPID: 0x07EB ProvID: 000000
*EMM: CaID: 0x187D -> CaPID: 0x07EC ProvID: 000000
*EMM: CaID: 0x187E -> CaPID: 0x07ED ProvID: 000000
[mg0] ECM: CaID: 0x1810 -> CaPID: 0x0858 ProvID: 000000
[mg0] ECM: CaID: 0x0100 -> CaPID: 0x0470 ProvID: 004106
EMM: RSA Nagra2 key not found for id 6a (pid 0x07E1)
EMM: RSA Nagra2 key not found for id 6a (pid 0x07E2)
[mg0] -> ECM sent to gbox xxxxxx.dyndns.org:xxxx pid 0x858 ( 4868 )
EMM: RSA Nagra2 key not found for id be (pid 0x009B)
EMM: RSA Nagra2 key not found for id 6a (pid 0x07DF)
EMM: RSA Nagra2 key not found for id 90 (pid 0x009B)
EMM: RSA Nagra2 key not found for id 6a (pid 0x07E0)
[cccamd] Card remove from xxxxxx.dyndns.org:12000 (xxxxxx)
[mg0] -> ECM to cccamd xxxxxx.dyndns.org:12000 (xxxxxx)
[mg0] cccamd route xxxxxx.dyndns.org:12000 cant decode (328ms)
EMM: RSA Nagra2 key not found for id 73 (pid 0x009B)
[mg0] cccamd route xxxxxx.dyndns.org:12000 cant decode (66ms)

...it goes on for a fair bit searching...

[mg0] 722 msec -- Thu Jan 21 10:42:58 2010
===== Seca ECM on CaID 0x0100, pid 0x0470 ======
prov: 004106
cw0:0 D6 0B C0 A1 DC AE 3F C9
cw1:0 A4 41 79 5E 74 F9 B9 26
EMM: RSA Nagra2 key not found for id 4 (pid 0x009B)
[mg0] -> ECM to cccamd xxxxxx.dyndns.org:12000 (xxxxxx)
EMM: RSA Nagra2 key not found for id 40 (pid 0x009B)
[mg0] <- CW from cccamd xxxxxx.dyndns.org:12000 (2069ms)
[mg0] 2069 msec -- Thu Jan 21 10:43:06 2010

...then it happens again... searching...

WARNING: card not found.

[mg0] WARNING, both cws changed !
[mg0] 598 msec -- Thu Jan 21 10:43:40 2010
===== Seca ECM on CaID 0x0100, pid 0x0470 ======
prov: 004106
cw0:0 E1 B3 D7 6B 75 D4 90 D9
cw1:0 79 06 19 98 22 D0 C2 B4


Bla, bla... so, as you can see, it works...:coolgleamA:

mushroom
21-01-2010, 12:32 PM
how many clines i can add? any limits?

deki20
21-01-2010, 12:36 PM
MultiCas vs. Mgcamd

speed?
stability?
NDS?

regards

rmt
21-01-2010, 12:54 PM
MultiCas vs. Mgcamd

speed?
stability?
NDS?

regards

mgcamd is more stable than multicas

rmt
21-01-2010, 01:20 PM
I didnt test the new cccam client capability.

But what i can say is that for newcamd client mode, mgcamd was faster than multicas.

Smudger
21-01-2010, 01:31 PM
I still having problems even on tv globo which I assume should clear.


Oh just cleared after reboot I'm off again to test.

and it works ok on 2.1.3.

Very pleased more testing. was unable to run from telnet but ok if allowed to run via Plugins. I have notice it shows like this

1186 root 1272 S /EMU/OpenXCAS/mgcamd/mgcamd
1188 root 1272 S /EMU/OpenXCAS/mgcamd/mgcamd
1189 root 1272 S /EMU/OpenXCAS/mgcamd/mgcamd
1190 root 1272 S /EMU/OpenXCAS/mgcamd/mgcamd
1191 root 1272 S /EMU/OpenXCAS/mgcamd/mgcamd


EMU and not PLUGINS although it is physically in the PLUGINS folder.

medmed
21-01-2010, 01:47 PM
i connect 10 server (2.0.11,2.1.0,2.1.1,2.1.2,2.1.3) all is ok .

cerci
21-01-2010, 03:44 PM
[QUOTE=goran;691573]Working VERY well... ;) Very good job, very cool!!! :)

Now, can we have Mbox added, too, please... :D

Oh, Kanber, m8: can we have a nice mgcamd.info plugin, please... :respect-054:

==============================
http://www.satpimps.co.uk/showthread.php?t=124685

goran
21-01-2010, 05:08 PM
No, cerci, that is one piece of info only, it seems to me...

Kanber's plugins are lovely, more complete and a great help... ;)

MGcamd is slower to open a channel but cool, nonetheless!;)

goran
21-01-2010, 05:10 PM
To run MGcamd from Telenet [PuTTy]:

start it, login with root and your passwrd [azbox or whatever you might have put in], then

cd /EMU/OpenXCAS/mgcamd -> hit ENTER on the keybaord

chmod 755 mgcamd -> hit ENTER

./mgcamd -> hit ENTER

see the data flow...;)

Carp95
21-01-2010, 06:04 PM
First glance-test ( uptime 15min )

Connecting to local CCcam 2.11 server with local 0100:00006A card.

- As fast as Multicas 1.62
- Does a faster Job sitching to Veronica channel ( all multicas version has problem with that one )

Looks very promising

Have tot test other CAID's

Settings:

G: { 32 }
P: { 02 }

And the prio as I posted and added the ignore.list

Advantage above Multicas

- Better prio settings possible
- Better Ignore settings possible
- Multi emu support
- EMM support



tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 21:34:06), Thu Jan 21 17:05:12 2010
mg uptime 00d 00h 20m 20s, service changes: 4, ecm processed: 94, lost cw warnings: 2

Box: uptime = 48635s, CPU load: 1 min 186368 / 5 min 168960 / 15 min 180736
RAM in bytes: total 102895616 / free 7004160 / shared 0 / buffers = 2072576
mgcamd: total memory allocated by malloc, in bytes: 184320 (180kb), chunks 146872

goran
21-01-2010, 07:25 PM
It's pretty stable at my end but...

When I lose it - I lose it for too long...

Reconnection is... well... I hope I can edit it to make it much better, because it can be really annoying...:smash:

[Maybe the cards are just a bit too far...? Have to check...]

pasa
21-01-2010, 07:34 PM
For me Multicas is much better.
Mgcamd is ok firsth few minutes after that a lot of freezing.

Smudger
21-01-2010, 07:38 PM
For me the mgcamd works better then Multicas for cccam client and thats al I use it for.

and incase you missed this:-



mgcamd info ok
openxcas.conf

[module]
name = mgcamd
daemon = mgcamd
version = 1.35a
# argument = -a 3
INFO = /tmp/ecm.info
REFRESH = 2

pasa
21-01-2010, 07:59 PM
Maybe I have done something wrong, but have a lot freezes.
Watching mainly nds

albaki77
21-01-2010, 08:05 PM
Testing on CAID 919 at 13 east (SD & HD) and works a perfect so far using 10 Clines.:party::respect-044::bravo-009::respect-040:

smoother than Multicas as of now

Will test others later:respect-067:

leerock
21-01-2010, 08:41 PM
well
can t work with 2.1.3 here
it logins to the server fine but i does not request ecms.....
started it via telnet.....

maybe it s got to do whether the server is on linux or a stb

mine is on linux

anyone tested it with a linux server 2.1.3 and works?

Smudger
21-01-2010, 09:10 PM
@Leerock I had the same problem trying to run via telnet after a reboot and allowed to start via plugins worked a treat. But not via telnet
I connect to a 2.1.3 server.

My server is on Debian and I could see the connection but no ecm's going through when runing via telnet.


I set all the settings mentioned in this tread first.

Carp95
21-01-2010, 09:50 PM
After full test:

Way better/faster then Multicas:respect-040:

It's a keeper

leerock
21-01-2010, 09:50 PM
ok the problem was that i should put mgcamd a priority up above multicas

and WOW!!!!
it s much more stable here!!!!
and slightly faster zapping on all packages....

Sly, nova, cyfra...

Great!!!!!!

pasa
21-01-2010, 10:29 PM
mgcamd works fine, my problem was that I put 1.35 instead 1.35a

leerock
21-01-2010, 10:43 PM
After a bit more testing it seems that it does not work stable enough with 2.1.3.....

After about 15 minutes it started freezing....

Same case with some old multicas versions that couldnt deal well with 2.1.3

Smudger
21-01-2010, 11:40 PM
I'm using a 2.1.3 debian server and not one freeze all night NDS 28.2 with latest firmware.
This cam for me is much better on 2.1.3 with smargo readers then MultiCas it handles the higher ecm's that MultiCas can't .

I do admit I go four pixelation's in 4 hours. my dreambox on cccam also did at the same time and that was a .440 ecm time.

I have set all the settings for priority list and cfg files mentioned at the start of this post but not the ignore list.

I did read problems with connecting to server on dreambox cccam 2.1.3

also I have no other cam or plugin enabled .

Although I am running rsync to copy my music and avi's to the harddrive at the same time from my server. So I expect my network and receivers cpu is working hard.

thanks :respect-049:

irishchris
22-01-2010, 01:30 AM
hi
i have followed all the steps here - thanks to all. but there are still few glitches when left for while on same channel. but it may be peer setup. is there anyway to check which peer cline is been used something similar to ccaminfo php but for this?

tx0
22-01-2010, 01:39 AM
tried w/2.1.3 srv and back to Multi. freezes while recording :(

massimo1167
22-01-2010, 08:07 AM
I've tried this version, but I come back to the old 1.33.
If I connect to Oscam server, or to cccam server (my DB7000), I have freeze every 5-10 minutes.

May someone post the right config file?

Who can explain how to configure 2 different mgcamd version at the same time on the same azbox, I've tried this configuration:

/EMU/OpenXCAS
|->mgcamd
|->mgcamd135
|->MultiCAS
|->sh
|addons.conf
|module.seq

[module.seq]

mgcamd
#mgcamd135
#MultiCAS


[opencas.conf] inside mgcamd (bin is called "mgcamd")

[module]
name = mgcamd
daemon = mgcamd
version = 1.33
# argument = -


[opencas.conf] inside mgcamd135 (bin is called "mgcamd135")

[module]
name = mgcamd135
daemon = mgcamd135
version = 1.35a
# argument = -a 3


The mgcamd135 bis was started but if I check the mgcamd log, stops after few steps, it can't connect to server.If a rename mgcamd135 (everything) to mgcamd everythings works (with freezes)

Carp95
22-01-2010, 10:02 AM
cfg files are in this topic main settings:


mg.cfg
G: { 32 } #CCcam client alone
G: { 33 } # CCam and Newcamd
G: { 41 } # CCcam, Newcamd, Gbox
Pick one off the above
P: { 02 } #CCcam, Newcamd, Radegast, Gbox

Problems reported with Cccam server 2.12 and 2.13 when server is in dreambox, if those versions are in a linux server all ok.

scalpel
22-01-2010, 10:27 AM
Hi, which version newcs is the best for using in azbox hd?

leerock
22-01-2010, 11:08 AM
Problems reported with Cccam server 2.12 and 2.13 when server is in dreambox, if those versions are in a linux server all ok.

No it s not ok

I m connecting to a linux 2.1.3 ubuntu linux server

the first 5-10 are fine with fast zapping and stability...
but after that, i get constant freezes....

when it gets to this point... it even struggles to reconnect...
even after reboot

tried all settings mentioned in here...
even smudger s , who s reporting no problems

deki20
22-01-2010, 11:46 AM
No it s not ok

I m connecting to a linux 2.1.3 ubuntu linux server

the first 5-10 are fine with fast zapping and stability...
but after that, i get constant freezes....

when it gets to this point... it even struggles to reconnect...
even after reboot

tried all settings mentioned in here...
even smudger s , who s reporting no problems

I agree with you...Same situation on my situation....
I am returned my linux server on 2.1.1, and all OK...

regards

goran
22-01-2010, 11:48 AM
Same here, leerock. Once it starts with troubles - not easy to reconnect, easy to "lose it again" etc.

Speaking as a lay person: "memory leak" or some such problem?

satlubitel
22-01-2010, 12:55 PM
Hi Goran, all,

I have 2 questions:

1. If I need to use it ONLY as a CCCam client and not Gbox, do I need to touch/edit peer.cfg as you suggetsed below?

M: { my.dyndns.org { mypass}}
#
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}

2. Does Mgcamd 1.35a depends on the FW version (i.e. I am with 3911, which is little bit old)

What I did so far is:
1. Edit the mg_cfg:
- G: { 32 }
- P: { 02 }
2. Renamed cccamd.list.example to cccamd.list and added my C line:
C: peer.DynDNS.something port username password
3. Send them to mgcamd folder
4. Gave CHMOD -> 755 to all files

NO Any luck so far...looking for the problem..
Cheers!

leerock
22-01-2010, 01:00 PM
Haven't checked memory goran but i don t think this is the case...
Coz once the freezes get started, after you kill mgcamd, multicas struggles to reconnect too...
Even after reboot...
You have to wait a few minutes and then try again...

Seems like sth is happening on server site..

Don t know how to say it in english...
It s like the server is blacklisting a specific client that shows strange behaviour, for a few minutes...

leerock
22-01-2010, 01:03 PM
Hi Goran, all,

I have 2 questions:

1. If I need to use it ONLY as a CCCam client and not Gbox, do I need to touch/edit peer.cfg as you suggetsed below?

M: { my.dyndns.org { mypass}}
#
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}
D: { peer’sserver.dyndns.something { myport hisport { hispass { A3 A3 }}}}

2. Does Mgcamd 1.35a depends on the FW version (i.e. I am with 3911, which is little bit old)




What I did so far is:
1. Edit the mg_cfg:
- G: { 32 }
- P: { 02 }
2. Renamed cccamd.list.example to cccamd.list and added my C line:
C: peer.DynDNS.something port username password
3. Send them to mgcamd folder
4. Gave CHMOD -> 755 to all files

NO Any luck so far...looking for the problem..
Cheers!

No m8
peer.cfg is for gbox

just edit cccamd.list...

your mg.cfg looks fine

ohh....
I use latest fw but i think it will work fine on older fw too

satlubitel
22-01-2010, 01:36 PM
thanks a lot leerock,

Well then strange..seem all is done correctly, but it doesnt start at all.
Multicas and CCCam 2.1.1 work though..
What might be the issue?

goran
22-01-2010, 01:43 PM
Use PuTTy to see what it says...

Start it, login with root and azbox for password [or whatever you may have changed it], then the following 3 commands, each followed by ENTER on your keyboard:


cd /EMU/OpenXCAS/mgcamd

chmod 755 mgcamd

./mgcamd

Copy and paste the log here but obscure the private bits!!!

leerock
22-01-2010, 02:51 PM
i had the same problem and has strangely been fixed by putting mgcamd first in priority above multicas

plugins-openxcas-activation and priority- priority up

goran
22-01-2010, 02:52 PM
I don't think so: mine was 4th from the top and it worked...

rmt
22-01-2010, 02:58 PM
I don't think so: mine was 4th from the top and it worked...

I dont think that priority plays a role, since azbox runs only one emu at a specific time.

All others are deactivated any way

So, it has nothing to compare with, to prefer

satlubitel
22-01-2010, 03:23 PM
Goran, I have done what U suggested.
Below is the result:

MMP[Mgcamd]$ ./mgcamd
warning, no config file
tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 21:34:06)
[mg] Net:0:7:0:10s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:6 Log:2:no ip:28007 Reread:0
[mg] Ecm cache time: 15
Box type: azbox
Conax.Key error 2: No such file or directory
SoftCam.Key error 2: No such file or directory
AutoRoll.Key error 2: No such file or directory
Conax.Key error 2: No such file or directory
[OPENXCAS_API:Fri Jan 22 14:07:05.759] openxcas_open:285 ## mgcamd
[OPENXCAS_API:Fri Jan 22 14:07:05.779] load_xcas_control:98 ## loaded controller ID = 0x19760507
osdep_msq_server_open : key_request 0x54C4D100 key_response 0x54C4D101
key(54c4d100), msgflg(448)
key(54c4d101), msgflg(448)
osdep_msq_client_connect : key_request 0x54C4D100 key_response 0x54C4D101
[mgcam] emm thread started

leerock
22-01-2010, 03:31 PM
i also had the no config file message and what i think has sorted it out was by naming the folder without capital "m" ......
mgcamd instead of Mgcamd

seems like the binary tries to find the config files in the installation folder and it s case sensitive...

satlubitel
22-01-2010, 03:39 PM
Hmmm,
I have taken from Goran's attchment -> post #10
http://www.satpimps.co.uk/attachment.php?attachmentid=39792&d=1264034675
Some other source?
Cheers!

leerock
22-01-2010, 03:47 PM
My mistake m8
if you ve downloaded gorans attachement then its fine

i ve edited my post

leerock
22-01-2010, 03:50 PM
I don't think so: mine was 4th from the top and it worked...

:)
yeah i know m8 it doesnt sound logical since all other cams are stopped..
Maybe it was a coincidence

satlubitel
22-01-2010, 04:01 PM
:-) Leerock, yessss the issue was the CAPITAL M....
Seems now all OK
:-) Cannot see actually the TV and picture as I am still in the office and do all remotelly but saw the I have connected the server when run ./mgcamd
Will see in about 2 hours when back home if reaaly works

leerock
22-01-2010, 04:08 PM
Nice :)

Also don t forget to do the same in your openxcas.conf....

don t know how much case sensitive openxcas is.....

Smudger
22-01-2010, 05:20 PM
I've just been experimenting and I still cannot get this to run in telnet session yet runs fine via plugin menu's.

well it runs in telnet but does not clear.

I still find it better then MultiCas for what I use it for no local cards.

Intresting info in file /tmp/mgstat.info


tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 21:34:06), Fri Jan 22 16:45:57 2010
mg uptime 00d 00h 27m 27s, service changes: 1, ecm processed: 206, lost cw warnings: 0

Box: uptime = 3247s, CPU load: 1 min 397184 / 5 min 404832 / 15 min 384576
RAM in bytes: total 102895616 / free 3231744 / shared 0 / buffers = 266240
mgcamd: total memory allocated by malloc, in bytes: 114688 (112kb), chunks 103504

------------------------------------------------------------------------------------------------------------------------------------------

tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 21:34:06), Fri Jan 22 16:53:04 2010
mg uptime 00d 00h 34m 34s, service changes: 1, ecm processed: 260, lost cw warnings: 0

Box: uptime = 3674s, CPU load: 1 min 412416 / 5 min 392960 / 15 min 384480
RAM in bytes: total 102895616 / free 2789376 / shared 0 / buffers = 262144
mgcamd: total memory allocated by malloc, in bytes: 114688 (112kb), chunks 106904

-------------------------------------------------------------------------------------------------------------------------

as I've said before I'm also runing Rsync copying files to my internal harddrive. So CPU etc maybe higher then normal.

kanber_kav
22-01-2010, 05:28 PM
Goran, I have done what U suggested.
Below is the result:

MMP[Mgcamd]$ ./mgcamd
warning, no config file
tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 21:34:06)
[mg] Net:0:7:0:10s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:6 Log:2:no ip:28007 Reread:0
[mg] Ecm cache time: 15
Box type: azbox
Conax.Key error 2: No such file or directory
SoftCam.Key error 2: No such file or directory
AutoRoll.Key error 2: No such file or directory
Conax.Key error 2: No such file or directory
[OPENXCAS_API:Fri Jan 22 14:07:05.759] openxcas_open:285 ## mgcamd
[OPENXCAS_API:Fri Jan 22 14:07:05.779] load_xcas_control:98 ## loaded controller ID = 0x19760507
osdep_msq_server_open : key_request 0x54C4D100 key_response 0x54C4D101
key(54c4d100), msgflg(448)
key(54c4d101), msgflg(448)
osdep_msq_client_connect : key_request 0x54C4D100 key_response 0x54C4D101
[mgcam] emm thread started


change Mgcamd folder name mgcamd

goran
22-01-2010, 05:35 PM
Yeah, he saw it, K_K...

Since you are here: can we have a nice MGcamd Info plugin by Kanber_Kav, please?:respect-050: :respect-048:

Carp95
22-01-2010, 06:06 PM
===== NDS ECM on CaID 0x0963, pid 0x0500 ======
prov: 000000
cw0: 91 16 88 2F 18 EA C9 CB
cw1: DD 68 8F D4 01 91 5F F1
Signature OK
source: net (cccamd at xxx.xxx.x.xx:xxxx)
221 msec -- Fri Jan 22 16:51:18 2010

Works like a charm on HD channels:respect-040:

Smudger
22-01-2010, 06:08 PM
Works like a charm on HD channels:respect-040:

Beat me to it > > works a treat on all channels..

satlubitel
22-01-2010, 06:43 PM
Hi all,

Some feedback: Well, all worked fine and after 10 min started to freeze
had to revert back to Multicas 1.62
Seems the version is still not stable
Will wait for next/better one
Cheers

ouTsiDaz_
23-01-2010, 02:58 AM
Can anyone connect to newcs starting mgcamd thru OpenXCAS?

I mean, if I start mgcamd in telnet, it connects to newcs right away and receives the card info. But when I start it with the remote, it only connects to CCcam, or when it connects to newcs, it doesn't get any card.

I'm gessing the problem is in the openxcas.conf, I'm using the defaults.

Here is the log of both cases.
Using remote:

[config] newcamd route = mgcamd:localhost:15050 server local
newcamd keep alive: 0, incoming port: 12001
CCcamd route: host 127.0.0.1 port 12000 xxxxx:xxxxx
[mgcam] emm thread started
[newcamd] Connecting to localhost:15050...
[cccamd] My nodeID da89ba8af9b0472e
[cccamd] =============== Connecting to 127.0.0.1:12000... ===============
[newcamd] Connection to localhost:15050 failed (6ms)
[cccamd] Connected to 127.0.0.1:12000 as xxxxx (4368ms)
[cccamd] Login to 127.0.0.1:12000 as xxxxx accepted (54ms)
[cccamd] Server intro from 127.0.0.1:12000
[cccamd] Server NodeID 7983e216f4aa50bd version 2.1.1
[mg0] service 66 index 0 pmt pid 0 (1)
EMM: CaID: 0x0100 -> CaPID: 0x0051 ProvID: 000000
EMM: CaID: 0x0100 -> CaPID: 0x0052 ProvID: 005211
EMM: CaID: 0x0100 -> CaPID: 0x0053 ProvID: 005221
[mg0] ECM: CaID: 0x0100 -> CaPID: 0x0402 ProvID: 005221

Starting thru telnet:

[mgcam] emm thread started
[newcamd] Connecting to localhost:15050...
[cccamd] My nodeID da89ba8af9b0472e
[cccamd] My nodeID da89ba8af9b0472e
[cccamd] =============== Connecting to 127.0.0.1:12000... ===============
[mg0] service 65 index 0 pmt pid 0 (1)
[mg0] ECM: CaID: 0x0100 -> CaPID: 0x0402 ProvID: 005221
EMM: CaID: 0x0100 -> CaPID: 0x0051 ProvID: 000000
EMM: CaID: 0x0100 -> CaPID: 0x0052 ProvID: 005211
EMM: CaID: 0x0100 -> CaPID: 0x0053 ProvID: 005221
[newcamd] Login to localhost:15050 as mgcamd accepted (28ms)
[cccamd] Connected to 127.0.0.1:12000 as xxxxx (18ms)
[newcamd] Card data from localhost:15050 (52ms):
EMM enabled: UA yes SA yes GA yes, Card serial: 4C4DC8BC
Userid 1 caid 100 providers 3
Idents: 005211 005221 005225
ids: 2626E45E 19D0F 0

[cccamd] Login to 127.0.0.1:12000 as xxxxx accepted (1085ms)
[cccamd] Server intro from 127.0.0.1:12000
[cccamd] Server NodeID 7983e216f4aa50bd version 2.1.1

deki20
23-01-2010, 09:03 AM
mgcamd info ok
openxcas.conf

[module]
name = mgcamd
daemon = mgcamd
version = 1.35a
# argument = -a 3
INFO = /tmp/ecm.info
REFRESH = 2


don`t work on me!?
I was try and small caps, only black box, no text....

Smudger
23-01-2010, 09:37 AM
it only works if channel unscrambled.

goran
23-01-2010, 10:06 AM
Can anyone connect to newcs starting mgcamd thru OpenXCAS?

I mean, if I start mgcamd in telnet, it connects to newcs right away and receives the card info. But when I start it with the remote, it only connects to CCcam, or when it connects to newcs, it doesn't get any card.

I'm gessing the problem is in the openxcas.conf, I'm using the defaults.

Try a shorter "wait" for NewCS and longer for MGcamd, when starting and maybe... ;)

openxcas.conf in NewCS folder


[module]
name = newcs
daemon = newcs
argument = -nd
version = 1.6
xcasapi = FALSEopenxcas.conf in mgcamd folder, as you have it in my "Alternative guide..."


In EMU/OpenXCAS/mgcamd folder edit the openxcas.conf to add


api = yes
wait = 15sec ...as we heard on this forum, so the sequence is NewCS first to read the card and then MGcamd or MultiCAS or Mbox to connect to it...

Good luck! :respect-051:

P.S. When you do it by remote controller - how exactly are you doing it?

I go to HOME -> Plug-ins etc.

Then, I hit Yellow button -> OK, then choose something you wanna start and OK -> OK again...

But in this case you want 2 to be started, so here is an idea: start NewCS first, then get out and start MGcamd by remote using the > >¦ button... ;)

ouTsiDaz_
23-01-2010, 02:04 PM
Try a shorter "wait" for NewCS and longer for MGcamd, when starting and maybe... ;)

openxcas.conf in NewCS folder

openxcas.conf in mgcamd folder, as you have it in my "Alternative guide..."

...as we heard on this forum, so the sequence is NewCS first to read the card and then MGcamd or MultiCAS or Mbox to connect to it...

Good luck! :respect-051:

P.S. When you do it by remote controller - how exactly are you doing it?

I go to HOME -> Plug-ins etc.

Then, I hit Yellow button -> OK, then choose something you wanna start and OK -> OK again...

But in this case you want 2 to be started, so here is an idea: start NewCS first, then get out and start MGcamd by remote using the > >¦ button... ;)

Thanks for the suggestion, but it didn't work.

Doesn't matter how you start it, by Plugins or > >|, restart all or start newcs first and then mgcamd or mgcamd first, doesn't connect to newcs.

Only by telnet.

tapper
24-01-2010, 12:03 AM
Hi I'm having probs with mgcamd



MMP[mgcamd]$ ./mgcamd
tuxbox mgcamd v1.35 by mixvt (compiled Jan 20 2010 21:34:06)
[mg] Net:32:7:2:5s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:7 Log:2:no ip:28007 Reread:0
[mg] Ecm cache time: 15
Box type: azbox
Keys readed
AutoRoll.Key error 2: No such file or directory
CCcamd route: host my cs server
[OPENXCAS_API:Sat Jan 23 22:57:28.931] openxcas_open:285 ## mgcamd
[OPENXCAS_API:Sat Jan 23 22:57:28.951] load_xcas_control:98 ## loaded controller ID = 0x19760507
osdep_msq_server_open : key_request ********* key_response *********
key(**********), msgflg(448)
key(*********), msgflg(448)
osdep_msq_client_connect : key_request ************ key_response *******
[mgcam] emm thread started
[cccamd] My nodeID ****************
[cccamd] =============== Connecting to from my cs server:12000... ===============
[cccamd] Connected to from my cs server as my login id (106ms)
[cccamd] Login to from my cs server as my login id accepted (168ms)
[cccamd] Server intro from my cs server
[cccamd] Server NodeID **************** version 2.1.3





It seems I get a connection but thats it, if I change channel it stays scrambled,

goran
24-01-2010, 01:00 AM
Try 2.1.1.

It works as an Emu, too [with keys].

You are trying to connect to your other box, which is a server, so it's a home network?

What are you settings?

tapper
24-01-2010, 11:42 AM
I'm connecting to a friends server hes got newcs + CCcam 2.13


the only option in mg_cfg Ive changed is G: { 32 }

and I have my server listed in CCcam.list

goran
24-01-2010, 12:06 PM
Prioritise CCcamd, then. Read above how to do that in _cfg file.

Also, priority and ignore lists can help...:coolgleamA:

tapper
24-01-2010, 12:33 PM
Ok I've got it working, but only via the remote, it wont clear any channels when started by a telnet session

Smudger
24-01-2010, 01:44 PM
Ok I've got it working, but only via the remote, it wont clear any channels when started by a telnet session

I had the same problem can't get it to clear via telnet but works fine with remote.

Smudger
27-01-2010, 08:29 PM
Can somone explain the reason why the 1.35a file in the files section is dated 26/01, is it a different 1.35a as the one in this thread.

when you run in telnet it show 1.35a and a compile date of 26/01/2010

vegekou
31-01-2010, 04:08 PM
Is it only me or after 5 mins of working flawlessly it just won't end freezing?

goran
31-01-2010, 04:17 PM
Sometimes it works better, strangely enough... or not...

It depends on one's network, too...

xanadu
31-01-2010, 05:41 PM
Is it only me or after 5 mins of working flawlessly it just won't end freezing?

I tried it but found it always freezes after about 20 minutes.

Have gone back to MultiCAS which works good enough.

EAYKOC
23-02-2010, 10:22 PM
Hi,

I don't know whether this is the right place to ask, if not please excuse me.

I have a d i gi turk subscription with a c ryp toworks card. I'm using newcs (the version that supports internal card reader) as the card server and gave the dummy user auto-update permission. In the mg_cfg file, I've setup mgcamd to auto-update.

While watching the TV, picture freezes for nearly 10 seconds and restarts again after 3-4 seconds.

When I setup mg_cfg to not make auto-updates then it doesn't freeze on any channels. But this time, I need to place my c w card into the original STB to make it update the card every week.

I've also tried using the latest MultiCAS (1.62B A07). I tried using only multicas and newcs + multicas combination. The result is the same.

Is there any other way/EMU that I won't need to place my card into another STB?

Thank you,

Eren

hanswurscht
24-02-2010, 07:29 PM
Hi,

I don't know whether this is the right place to ask, if not please excuse me.

I have a d i gi turk subscription with a c ryp toworks card. I'm using newcs (the version that supports internal card reader) as the card server and gave the dummy user auto-update permission. In the mg_cfg file, I've setup mgcamd to auto-update.

While watching the TV, picture freezes for nearly 10 seconds and restarts again after 3-4 seconds.

When I setup mg_cfg to not make auto-updates then it doesn't freeze on any channels. But this time, I need to place my c w card into the original STB to make it update the card every week.

I've also tried using the latest MultiCAS (1.62B A07). I tried using only multicas and newcs + multicas combination. The result is the same.

Is there any other way/EMU that I won't need to place my card into another STB?

Thank you,

ErenMulticas maybe, dont know if it update your EMMs.
Another Way is over Newcamdprotocol to a CCcamserver and Remote EMMs

EAYKOC
25-02-2010, 02:48 PM
Multicas maybe, dont know if it update your EMMs.
Another Way is over Newcamdprotocol to a CCcamserver and Remote EMMs

Hi hanswurscht,

MultiCAS alone, makes card updates but it freezes frequently. Enabling auto-update on both MultiCAS and newcs and using newcamd protocol freezes also. I haven't tried another protocol for newcs + multicas or newcs + mgcamd combinations and I don't think that may change anything.

Anyway thank you for your reply.. I think I'll keep praying for a better version of MultiCAS that may solve my problem.. :respect-053:

Eren

jumbotroll
25-02-2010, 03:29 PM
Hi, here is a working solution.
AZbox HD premium plus.

I am running NewCS 1.67 RC1 with smargo smartreader+ firmware 1.4.

Smargo settings:
Autoswicth, T1 (NDZ card)
Kernel = normal.

Newcs in phoenix mode.
newcs.xml settings:

<name>smargo</name>
<type>phoenix</type>
<mhz>369</mhz>
<node>/dev/ttyUSB0</node>
<parity>odd</parity>
<reset>normal</reset>

openxcas.conf in newcs folder looks like this.
[module]
name = newcs
daemon = newcs
argument = -c /PLUGINS/OpenXCAS/newcs/newcs.xml
version = 1.67 RC1
xcasapi = FALSE

mgcamnd 1.35a
Change settings in mg_cfg :
# newcamd dead routes connect retry, sec
Q: { 10 }
# network ecm timeout in seconds
K: { 15 }

Jumbotroll

EAYKOC
26-02-2010, 12:05 PM
I am running NewCS 1.67 RC1 with smargo smartreader+ firmware 1.4.
...
Jumbotroll

Thank you for this valuable info. I guess I can give it a try..

I'm also considering purchasing a cam module for my card. I've looked up the prices for smartgo and cam module, they were nearly the same..

Eren

Mangasora
26-02-2010, 04:07 PM
Can anyone connect to newcs starting mgcamd thru OpenXCAS?

I mean, if I start mgcamd in telnet, it connects to newcs right away and receives the card info. But when I start it with the remote, it only connects to CCcam, or when it connects to newcs, it doesn't get any card.

I'm gessing the problem is in the openxcas.conf, I'm using the defaults.

Here is the log of both cases.
Using remote:

[config] newcamd route = mgcamd:localhost:15050 server local
newcamd keep alive: 0, incoming port: 12001
CCcamd route: host 127.0.0.1 port 12000 xxxxx:xxxxx
[mgcam] emm thread started
[newcamd] Connecting to localhost:15050...
[cccamd] My nodeID da89ba8af9b0472e
[cccamd] =============== Connecting to 127.0.0.1:12000... ===============
[newcamd] Connection to localhost:15050 failed (6ms)
[cccamd] Connected to 127.0.0.1:12000 as xxxxx (4368ms)
[cccamd] Login to 127.0.0.1:12000 as xxxxx accepted (54ms)
[cccamd] Server intro from 127.0.0.1:12000
[cccamd] Server NodeID 7983e216f4aa50bd version 2.1.1
[mg0] service 66 index 0 pmt pid 0 (1)
EMM: CaID: 0x0100 -> CaPID: 0x0051 ProvID: 000000
EMM: CaID: 0x0100 -> CaPID: 0x0052 ProvID: 005211
EMM: CaID: 0x0100 -> CaPID: 0x0053 ProvID: 005221
[mg0] ECM: CaID: 0x0100 -> CaPID: 0x0402 ProvID: 005221

Starting thru telnet:

[mgcam] emm thread started
[newcamd] Connecting to localhost:15050...
[cccamd] My nodeID da89ba8af9b0472e
[cccamd] My nodeID da89ba8af9b0472e
[cccamd] =============== Connecting to 127.0.0.1:12000... ===============
[mg0] service 65 index 0 pmt pid 0 (1)
[mg0] ECM: CaID: 0x0100 -> CaPID: 0x0402 ProvID: 005221
EMM: CaID: 0x0100 -> CaPID: 0x0051 ProvID: 000000
EMM: CaID: 0x0100 -> CaPID: 0x0052 ProvID: 005211
EMM: CaID: 0x0100 -> CaPID: 0x0053 ProvID: 005221
[newcamd] Login to localhost:15050 as mgcamd accepted (28ms)
[cccamd] Connected to 127.0.0.1:12000 as xxxxx (18ms)
[newcamd] Card data from localhost:15050 (52ms):
EMM enabled: UA yes SA yes GA yes, Card serial: 4C4DC8BC
Userid 1 caid 100 providers 3
Idents: 005211 005221 005225
ids: 2626E45E 19D0F 0

[cccamd] Login to 127.0.0.1:12000 as xxxxx accepted (1085ms)
[cccamd] Server intro from 127.0.0.1:12000
[cccamd] Server NodeID 7983e216f4aa50bd version 2.1.1


In OpenXCAS menu mgkamd comes first. Start mgcamd with OpenXCAS, kill mgcamd with script and run it again,start and newcs. In this way works for me.

EAYKOC
05-03-2010, 04:54 PM
Thank you for this valuable info. I guess I can give it a try..

I'm also considering purchasing a cam module for my card. I've looked up the prices for smartgo and cam module, they were nearly the same..

Eren

Hi again.

I've finally purchased a CI module for digiturk and the freezes are gone. Now I've another problem...

Without the CI module, using any one of the emu-cardreader combination I can add or remove subtitles to channels and change audio language, but with the CI module I cannot add subtitles even though I can change the audio language.

Do you have any idea why this may happen?

Thanks,

Eren

killerno
10-03-2010, 02:46 AM
Hi!

please somebody hellp me.I'm running a cccam server on my box and using mgcamd as a client.everything is working perfect, but if i restart my box mgcamd don't connect to the server(i think server wakes up after 10 sec).I tried to restart only mgcamd, but if i restart it cccam server restart as well.Is there any solution to connect manually to the server?thx

wackaman
05-04-2010, 12:44 PM
Today I have donwloaded Satpimps MGCamd 1.35a too.
Now I have installed on my AZBOX for use as CCcam-Client.
I have edited mg_cfg with:
- G: { 32 }
- P: { 02 }
Rest like the manual from Side 1.

Everything works fine.
Still to now no freezes. Using since 1 Hour.

But I use an other mg_cfg for use the HD+ as the orign in Package.

With MGCamd 1.35 (without a) I have much Problems after 15 to 20 Minutes with rythm. Freezes.
With 1.35a from here not.

Many thanks to you all.

Sh... happens...

After 1 Hour and 2 Minutes Freezes every 10 Seconds for 5 Seconds.
In OpenXcas Menue Restard MGcamd and no Freezes for the next Hour.

Is it possible to create a Script to restard MGcamd automatic after 60 Minutes?

leerock
05-04-2010, 05:59 PM
Today I have donwloaded Satpimps MGCamd 1.35a too.
Now I have installed on my AZBOX for use as CCcam-Client.
I have edited mg_cfg with:
- G: { 32 }
- P: { 02 }
Rest like the manual from Side 1.

Everything works fine.
Still to now no freezes. Using since 1 Hour.

But I use an other mg_cfg for use the HD+ as the orign in Package.

With MGCamd 1.35 (without a) I have much Problems after 15 to 20 Minutes with rythm. Freezes.
With 1.35a from here not.

Many thanks to you all.

Sh... happens...

After 1 Hour and 2 Minutes Freezes every 10 Seconds for 5 Seconds.
In OpenXcas Menue Restard MGcamd and no Freezes for the next Hour.

Is it possible to create a Script to restard MGcamd automatic after 60 Minutes?

this version has probs when connecting to cccam versions above 2.1.1

If you have probs why do you want to make it restart every hour and dont you just use multicas which is the stablest cccam client at the moment?

wackaman
05-04-2010, 06:56 PM
I knwo that MultiCas is verry stable, but I have the Problem, that ORF 1, ORF 2, ORF HD and ATV+ needs a verry long time to open with MultiCas.
Needs Up to 40 - 50 Seconds by Switching from a, for example Free TV Channel or Sky to on from the ORF Channels.
Switching from ORF 1 to ORF 2 needs only 2 Seconds.
With MGCamd ist only allways 1 - 2 Seconds.
I cant fix the Problem with MultiCas and ORF so I have tried out MGCamd.

So if anyone has the answer to fix the ORF Problem, tell it me please.

rtificial
05-04-2010, 06:59 PM
You could try if the prio file can improve this. I have had similar issues with the c+NL package until I changed the prio.

wackaman
05-04-2010, 07:41 PM
The Problem is, that I dont know how to create a prio file...
I have looked in go..le long times, but nothing found for german area.

Do you know the structur / format from priocaid.list?

rtificial
05-04-2010, 09:04 PM
If noone Posts in the meantime, i'll post mine as an example tomorrow

wackaman
05-04-2010, 09:30 PM
Thats a nice idea.

Thanks.

rtificial
08-04-2010, 08:21 PM
Sorry sorry, completely forgot...


### 0100 : SECA
### 0500 : VIACCESS
### 06xx : IRDETO
### 0dxx : CRYPTOWORKS
### 0bxx : CONAX
### 09xx : NDS
### 17xx : BETACRYPT
### 18xx : NAGRA
###----------------------------------------------------
### max 8 of caid 0100 0500 0600 0900 1800 0d00 0b00 1700
###----------------------------------------------------
### CASE OLD #1 0600 0d00 1700 1800 0900 0b00 0100 0500
### CASE OLD #2 0100 1800 0500 0600 0d00 1700 0b00 0900
###---------------------------------------------------
0100 1801 0500 0d00 1702 0b00 0963 093B

### Seca provider priority e.g. 6A has higher priority than 6C (Max 8).
0100 : 006A 006C 0068 4106 0081 0084 0085

### Viaccess provider priority e.g. 023B00 has higher priority than 020810 (Max 8).
0500 : 023B00 020810 020820 021110 020A00 032000 032010 024410

Enjama88
12-04-2010, 09:15 AM
Can anyone upload for me version 1.31 Mgcamd ? I heard that it is most stability version of Mgcamd.

EAYKOC
12-04-2010, 02:21 PM
Can anyone upload for me version 1.31 Mgcamd ? I heard that it is most stability version of Mgcamd.

I've downloaded this file some time ago but never tried it. So I don't know if it works.

Eren

Dorvita
18-01-2011, 05:52 PM
Hiya, this version suitable for a DM?
many thanks.Dor x

EAYKOC
19-01-2011, 02:10 PM
Hiya, this version suitable for a DM?
many thanks.Dor x

Hi,

If you're asking about the one I've uploaded (mgcamd 1.31), that is only for Azbox original firmware.

Eren

betas
30-06-2012, 10:03 PM
Hi guys.

Just wondering on where to place the SoftCam.key, AutoRoll.Key and constant.cw files? Have tried /var/keys/ as mg_cfg says and chmodded the dir + keys to 777 but it still wont work. Have also tried/var/etc/keys and /etc/keys!

Furthermore, upon reboot, any changes to /var are deleted and a factory /var is restored. Any ideas?

Regards,
Betas

gerard1
18-09-2012, 06:17 PM
Hi,
The response for above is the same folder as mg_cfg.

Now I've a question about the number of emus that can rum at the same time on openxcas. it seems to me only one witch is in the top priority the second and below are not working even if I restart them. Can any of you confirm this please and if not can you give the config to have more than one running at the same time.
(I've mutilcas as client and mgcamd as emukeys on OFW 54.02 on elite)
Regards
Gerard

zeini
19-09-2012, 08:35 AM
Yes, only one EMU can run at same time.

gerard1
19-09-2012, 08:20 PM
Hi Zeini
Thanks again for your response. Apparently the the list of emu and the priority option is useless.