PDA

View Full Version : Multicas and CCCAM



Pages : 1 [2]

leerock
11-10-2009, 03:18 PM
I don t have any freezes with native cccam(terrorman's script)....
It s just too slow on zapping and most times it needs back and forth zapping for a channel to open.....
With multicas i had the same problem since it started supporting cccam....
The first 15 minutes are very good....
Fast zapping and performance....
I do not have any freezes even on ndz....
But after those 15 minutes i get a big freeze(8secs)...
And then every 3 minutes i get the same freeze....
It s very strange coz this is exactly what s happening after i run multicas...
Same freezes at exactly the same time....
It s like it works with a clock or sth... :-)
and this is on all encryptions....
Ndz is a little worse offcourse.....
After that 15 minutes it s going nuts....
i don t only have those traditional big freezes every 3 minutes but also many small ones in between...

I guess there is a cccam server 2.1.2 incompatibility coz many in here report the same problems when connecting with that version....

Pls opensat fix that....
This is driving me nuts coz multicas is the best performing cccam client for me, but only on those first 15 mins...
I need a cccam client that works like that all the time...
:-)

SAUS04
11-10-2009, 04:19 PM
freezing on AZBOX is mainly down to network restrictions on the reciever itsself. nothing to do with CCcam IMHO


:beatdeadhorse5:

goran
11-10-2009, 04:25 PM
No, m8, that would be wrong, from what little I know. If you try Mbox and it's fine - then it's down to CCCam hack, with an "interceptor/mediator". We also have another mediator for all of them [OpenXCAS] and so on... Too many...

The net speed is more than adequate for CS!

The problem is with [W]LAN and USB transfers/streaming! To do with a bad driver, down to Sigma people - the processor crashing at higher speeds...

Good luck!

leerock
11-10-2009, 05:16 PM
It has nothing to do with network restrictions...
As i said , cccam native don t have any freezes...
Neither multicas on the first 15 mins...

If network restrictions was the problem i would be having freezes on both of those cases....

CS doesnt need that much of a bandwidth....

All things indicate that its a milticas problem....
Maybe only when connecting to a 2.1.2 server...

massimo1167
11-10-2009, 05:24 PM
No, m8, that would be wrong, from what little I know. If you try Mbox and it's fine - then it's down to CCCam hack, with an "interceptor/mediator". We also have another mediator for all of them [OpenXCAS] and so on... Too many...

The net speed is more than adequate for CS!

The problem is with [W]LAN and USB transfers/streaming! To do with a bad driver, down to Sigma people - the processor crashing at higher speeds...

Good luck!
So the problem is due to bugged Sigma driver o implementation in azbox firmware?
Do you know if there are new drivers from sigma people to solve this problems?

PS:
I agree, freezing problem isn't due to [W]Lan speed limitation!
Verify server!!!

SAUS04
11-10-2009, 05:25 PM
The problem is with [W]LAN and USB transfers/streaming! To do with a bad driver, down to Sigma people - the processor crashing at higher speeds...


Thats what i meant! opensat have restrictions in the firmware for lan wlan and usb transfer speeds to stop the box crashing due to por sigma drivers .. until this is fixed will not get decent cccam on this box..

One idea i think would work is to copy diablo wifi cccam in cam settings theres an option for delay. this delays the emm signal and fixes some freezing issue couldnt they port this into a azbox cccam of multicas ?

goran
11-10-2009, 05:37 PM
No, you do not understand! Read slowly, please!

The speed is great enough - no problems for CS!!!!!!!!! Never mind which CS SW!

Just the streaming transfers are the problem, which are really demanding, when you want to watch something from your PC or external HDD!!!!!!!!!!

I said, if Mbox is OK for CS [and it is pretty darn good!!], then CS is fine with those speeds, no problem whatsoever!!!!!! It's the CCcam hack that is the problem!!!

SAUS04
11-10-2009, 05:40 PM
sowwy i choose to disagree its the firmware in the box thats at fault like many issues hardware is top notch firmware is pants!:victory-045::respect-056:

goran
11-10-2009, 05:49 PM
No, you just don't understand and now you're stubborn on top...:banghead:

leerock
11-10-2009, 05:53 PM
jesus guys.....

do you even read what i write?

CCcam native is FINE....
CCC 0.2 is FINE....

i only have freezes with multicas......

if SERVER was the problem or NETWORK or ANYTHING ELSE i would be having freezes on those too.....

I ONLY HAVE FREEZES WITH MULTICAS!!!!!!!!!!!!!!!!!!!!!!!!! !

And as Goran said.....
Mbox is FINE....

SO DON'T BLAME THE FIRMWARE OR DRIVERS FOR THIS PROBLEM.....
BLAME THEM FOR ANYTHING ELSE....
IT S COMMON SENSE
JESUS!!!!!!

goran
11-10-2009, 06:02 PM
Well, I have problems with "Native CCcam" - after 4 or so zaps... it's stuck! Especially if it's faster zapping!!! Mbox doesn't have the same problem! As many of us have written!

MultiCAS has freezes [even the newest version] after a few minutes or maybe longer - but it gets stuck eventually... although it's better than the first version! There is progress!!!

Mbox is much better, still - agreed!

kleinerjunge
11-10-2009, 07:24 PM
I don t have any freezes with native cccam(terrorman's script)....
It s just too slow on zapping and most times it needs back and forth zapping for a channel to open.....
With multicas i had the same problem since it started supporting cccam....
The first 15 minutes are very good....
Fast zapping and performance....
I do not have any freezes even on ndz....
But after those 15 minutes i get a big freeze(8secs)...
And then every 3 minutes i get the same freeze....
It s very strange coz this is exactly what s happening after i run multicas...
Same freezes at exactly the same time....
It s like it works with a clock or sth... :-)
and this is on all encryptions....
Ndz is a little worse offcourse.....
After that 15 minutes it s going nuts....
i don t only have those traditional big freezes every 3 minutes but also many small ones in between...

I guess there is a cccam server 2.1.2 incompatibility coz many in here report the same problems when connecting with that version....

Pls opensat fix that....
This is driving me nuts coz multicas is the best performing cccam client for me, but only on those first 15 mins...
I need a cccam client that works like that all the time...
:-)

I can confirm THE SAME problems like you! Connecting to CCcam server v2.0.11 and v2.1.1 here!

I agree with you: MultiCAS best CCcam client until now on Azbox! Hoping Opensat fixes these problems soon!!

cu
KJ

leerock
11-10-2009, 07:32 PM
well....
as i said on my other post i do not have freezes when connecting to 2.0.11 with multicas

actually it works pretty good!!!

tx0
13-10-2009, 10:07 AM
could anyone explain me the meaning of priocaid.cfg in Multicas? what this configuration is about? Do I need to change it and when? Thanks.

goran
13-10-2009, 01:07 PM
See my Alternative Guide under Mbox - prio etc. files.

Cheerio!:respect-051:

aqa
14-10-2009, 01:12 PM
multicas is Definitely getting better latestone seems to decrypt quite quickley version 1.60D-A02 less freezing as well..

tsakman
14-10-2009, 01:13 PM
MultiCAS_v160D-A02_2k91013

FIXED BUGS


http://www.filesavr.com/multicasv160da022k91013

enrico001u
14-10-2009, 01:47 PM
yes all that needs to be done is copy new files and overwrite old

working fine make sure you chmod the emu module again to 755

bcrazynutter
14-10-2009, 01:50 PM
MultiCAS_v160D-A02_2k91013

FIXED BUGS


http://www.filesavr.com/multicasv160da022k91013

'Fixed bugs' - Is this now fully compatible with 2.1.2?

goran
14-10-2009, 01:57 PM
Updated online -> Download Executables, then Download Config -> it updated but saved my server details!!! Nice!!!!!!!:respect-023:

Rebooted, just to test if it will still be all there - and it was!!!:respect-054:

Cool!!!!!!!!!!:sifone:

gtg60
14-10-2009, 02:10 PM
Well, hats off to the developers:bow-004:

The constant updates to MultiCAS recently have been fantastic! If only the Firmware was seeing such development!

enrico001u
14-10-2009, 02:22 PM
has any one managed to get the prio working correctly
I have entered

0963 093b

but still refers to 919 and 961

iv noticed if i am recieving a share from a peer lets say sky italia and then switch over to sky uk it will get sky uk from the same peer instead of using mine.

anyone else noticed this problem?

rmt
14-10-2009, 02:28 PM
Updated online -> Download Executables, then Download Config -> it updated but saved my server details!!! Nice!!!!!!!:respect-023:

Rebooted, just to test if it will still be all there - and it was!!!:respect-054:

Cool!!!!!!!!!!:sifone:

Hi goran,

How can we see the version of the new installed one?

I mean, can we be sure that the new installed one overtook the current settings there (and not the old one)?

Thanks

goran
14-10-2009, 02:31 PM
It says on top of the AZbox HD window... ;)

aqa
14-10-2009, 02:31 PM
Hi goran,

How can we see the version of the new installed one?

I mean, can we be sure that the new installed one overtook the current settings there (and not the old one)?

Thanks

check itwith ftp

rmt
14-10-2009, 02:35 PM
ok I will try it, thanks

It is really getting better

hfmls
14-10-2009, 02:47 PM
amazing zapping speed.

hispasat
connected to 2 clines. awsome! no freezes.

sanca
14-10-2009, 03:00 PM
Hi

Showtime pacote não funciona, os cartões Irdeto não são bem gerenciados, Nall

hfmls
14-10-2009, 03:02 PM
english...

hispasat:
nagra 3 and seca all good and fast. no freezes.

rtificial
14-10-2009, 03:41 PM
is it getting as stable as mbox now?

hfmls
14-10-2009, 03:42 PM
well...better than 06 (06 has many freezes)

almost as 04 (really stable)

hanswurscht
14-10-2009, 03:52 PM
hmm, with new 3501 Mbox doesnt start anymore automatic.
Have fresh installed but... no Way.
These Plugins Shit dont work very well with mbox I think

hfmls
14-10-2009, 03:54 PM
insides OpenXCAS
create a openxcas.conf
and put something like this:




[modules]
count = 1
active_auto = true
active_1 = MboxCAS


[module_1]
ap = yes
name = MboxCAS
daemon = Mbox_module /PLUGINS/OpenXCAS/MboxCAS/mbox.cfg
xcasapi = TRUE
wait = 13 sec
version = 0.4-23

rtificial
14-10-2009, 03:55 PM
I have very few freezes in 06, and no problem with 3501 either.

I will give multicas a try.

hfmls
14-10-2009, 03:58 PM
how many peers do u have in 06? 06 only works ok with 20 peers or less.

leerock
14-10-2009, 04:08 PM
did they fix the cccam 2.1.2 problems?

hfmls
14-10-2009, 04:15 PM
well i'm using latest version of Multicas
and connect to 2 2.1.2 clines (u can check with multicas edit 1.2 :) )

all good, no freezes, opens all channels.
zapping is extremely fast.

goran
14-10-2009, 04:20 PM
hmm, with new 3501 Mbox doesnt start anymore automatic.
Have fresh installed but... no Way.
These Plugins Shit dont work very well with mbox I think

Works here, m8...;)

sanca
14-10-2009, 04:28 PM
CCcammal que funcionam bem?

hfmls
14-10-2009, 04:39 PM
english, can't u read?

sanca
14-10-2009, 04:50 PM
Yes read

My server CCcam 2.0.9

Irdeto (showTime ) no

Orange package no

Dolce NDS problem

hfmls
14-10-2009, 04:53 PM
did u try 2.1.2 cccam?

Smudger
14-10-2009, 04:58 PM
testing 2.1.2 now on 28.2

sanca
14-10-2009, 04:59 PM
Rata up to now and tested

hfmls
14-10-2009, 05:02 PM
what does that mean?


try 2.1.2 not 2.1.12

sanca
14-10-2009, 05:09 PM
then what will?

sami8519
14-10-2009, 05:09 PM
working download link please... the previous link did not work for me

hfmls
14-10-2009, 05:13 PM
then what will?

what?!?!

can u please talk english ?

jesus.

sanca
14-10-2009, 05:18 PM
which one conected ?

Smudger
14-10-2009, 05:20 PM
Sorry guys got a freeze after 7 mins on 2.1.2 on 28.2 using caid 0963 SD.
recovered it's self but enough for the scamble to just appear.
Then stable for 12 mins and then a quick 2 sec pause which I've seen with dream before. so far totally watchable.

still testing will test hd next.

:hurray: will give it 97% for me

also no freezing when channel selection screen is up.

Smudger
14-10-2009, 05:21 PM
working download link please... the previous link did not work for me

it's on the plugin download on box.

hanswurscht
14-10-2009, 05:25 PM
some Things to clear, dont understand because too many Changes in Versions.

1. In Server and Clientversion(only interesting one) what we have to do in example-cardkeydata.txt, nothing for Cards like ORF?
2. whats to do in splitterdata.txt, do we need this because there is a cccam.cfg and also a splitterdata.bin

A lot of Irritation for me, because I think splitterdata.txt not needed anymore.
splitterdata.bin is written automatic when Mcas is finding a Card, so we need only cccam.cfg for the Client?
I dont have a testing one, so I must ask for how its working, sorry

hfmls
14-10-2009, 05:32 PM
which one conected ?

i quit to answer your questions.


u make no sense to anyone.

hfmls
14-10-2009, 05:34 PM
some Things to clear, dont understand because too many Changes in Versions.

1. In Server and Clientversion(only interesting one) what we have to do in example-cardkeydata.txt, nothing for Cards like ORF?
2. whats to do in splitterdata.txt, do we need this because there is a cccam.cfg and also a splitterdata.bin

A lot of Irritation for me, because I think splitterdata.txt not needed anymore.
splitterdata.bin is written automatic when Mcas is finding a Card, so we need only cccam.cfg for the Client?
I dont have a testing one, so I must ask for how its working, sorry

i dont use spliiterdata

i used carddata to read from local then clines to connect to cccam. :)

Smudger
14-10-2009, 05:39 PM
Sorry guys got a freeze after 7 mins on 2.1.2 on 28.2 using caid 0963 SD.
recovered it's self but enough for the scamble to just appear.
Then stable for 12 mins and then a quick 2 sec pause which I've seen with dream before. so far totally watchable.

still testing will test hd next.

:hurray: will give it 97% for me

also no freezing when channel selection screen is up.

Well been on HD and it's as stable as SD never seen the scambled sign again so might be just a one off. This is now so close to being perfect.
I'll now give a 99% still may need a little tweak try it and you'll see what I mean. I have seen this on normal cccam on dream.
:respect-037: I'll not be going back to native cccam this time. Multicas has now been running 45 mins.
Need someone to watch a movie.

hfmls
14-10-2009, 05:42 PM
:)


now they can start working in cccam server.

or maybe multicas server+client (allready working, but only with 1 user)

more than 1 user? like 50 users? :)
that would be great.

hanswurscht
14-10-2009, 05:46 PM
i dont use spliiterdata

i used carddata to read from local then clines to connect to cccam. :)

OK, but not clear :)
There is a splitterdata.bin, when Mcas find a Card, so far OK, but where put I my Clines from Other and where do I give my Serverline in?

Cardkeydata is only for Boxkey and so on and nothing else, maybe also for IPK and UCPK

But we have also a plitterdata.txt with Lines (I think unused now with new Versions??) and a cccam.cfg

So what do I do with cccam.cfg?
Do I my Work as a real cccam?
Which Parameter are allowed?
Which really needed

A lot of Questions but it must be clear for all

Smudger
14-10-2009, 05:48 PM
just started getting regular freezes after 1 hour.
Maybe my server guy.

hfmls
14-10-2009, 05:49 PM
OK, but not clear :)
There is a splitterdata.bin, when Mcas find a Card, so far OK, but where put I my Clines from Other and where do I give my Serverline in?

Cardkeydata is only for Boxkey and so on and nothing else, maybe also for IPK and UCPK

But we have also a plitterdata.txt with Lines (I think unused now with new Versions??) and a cccam.cfg

So what do I do with cccam.cfg?
Do I my Work as a real cccam?
Which Parameter are allowed?
Which really needed

A lot of Questions but it must be clear for all

cccam.cfg file is just to paste some clines so u can go to plugins menu interface in azbox hd and load them, them press save and they will be saved in splitterdata.bin


multicas only connects to a cccam server, it doesn't serve...yet :)


u can conect to cccam clines.
and also use you local card at the same time. just put your values in cardkeydata.txt

;)

hanswurscht
14-10-2009, 05:50 PM
and next Question is, when I will use telesats Multicasedit 2.0 I get an Error on cccam Status when I use Button read
Get a Crash File not found and then Laufzeitfehler, always with his Tools....

hanswurscht
14-10-2009, 05:52 PM
cccam.cfg file is just to paste some clines so u can go to plugins menu interface in azbox hd and load them, them press save and they will be saved in splitterdata.bin


multicas only connects to a cccam server, it doesn't serve...yet :)


u can conect to cccam clines.
and also use you local card at the same time. just put your values in cardkeydata.txt

;)

OK, thx, but then I have some missunderstoods.
Multicas has in Setting Server AND Client, for what?

sami8519
14-10-2009, 05:54 PM
When Showtime will be supported :(

Smudger
14-10-2009, 05:54 PM
and next Question is, when I will use telesats Multicasedit 2.0 I get an Error on cccam Status when I use Button read
Get a Crash File not found and then Laufzeitfehler, always with his Tools....

may sure you uninstall all version on his multicasedit before installing latest I had problems until I done this.

version 2.0? I have 1.2a

hfmls
14-10-2009, 05:54 PM
OK, thx, but then I have some missunderstoods.
Multicas has in Setting Server AND Client, for what?

for multicas protocol.

only one peer at the moment


u serve your card to a friend
your friend servers his card to you.


if we could get like 50 peers. it would be cool :)

hfmls
14-10-2009, 05:55 PM
and next Question is, when I will use telesats Multicasedit 2.0 I get an Error on cccam Status when I use Button read
Get a Crash File not found and then Laufzeitfehler, always with his Tools....

use MULTICAS EDIT 1.2a

sami8519
14-10-2009, 06:11 PM
another bug: Sky Germany Nagra did not work.

mushroom
14-10-2009, 06:34 PM
tesdted it on many providers on hotbird and 16e.i get a lot of freezing on all channels only digitalb went great.nova dont open at all.with cccam 0.2 i dont have these problems.any suggestions?

enrico001u
14-10-2009, 06:43 PM
Hi guys does this prio look correct to you?
I am trying to prefer 963 and 93b.
I have the file called priocaid.cfg

### 0100 : SECA
### 0500 : VIACESS
### 06xx : IRDETO
### 0dxx : CRYPTOWORKS
### 0bxx : CONAX
### 09xx : NDS
### 17xx : BETACRYPT
### 18xx : NAGRA
###----------------------------------------------------
### max 8 of caid 0100 0500 0600 0900 1800 0d00 0b00 1700
###----------------------------------------------------
### CASE OLD #1 0600 0d00 1700 1800 0900 0b00 0100 0500
### CASE OLD #2 0100 1800 0500 0600 0d00 1700 0b00 0900
###---------------------------------------------------
0100 1800 0500 0600 0d00 1700 093b 0963



still goes for 961 on hop2 rather than 963 with quicker ecms on hop1

any ideas?

thanks

hanswurscht
14-10-2009, 07:10 PM
for multicas protocol.

only one peer at the moment


u serve your card to a friend
your friend servers his card to you.


if we could get like 50 peers. it would be cool :)

Lets make a Resume, to understand, my head is cooking ;)


If I will use Splitter & CLient (its the only one which makes sense for me, CS is a take AND give and not only Line crapping) so I can take only one Line from a CCcam Server?
And how I give him my Line ?
C: my Dyndns, my Port, but which Parameter, which Passwort?
I dont find any Things like Passwort and Paramters.

And can I share only with other AZHD or with any CCcam Server?


If I cant, this thing is useless for now, one Line is a Joke(without any fallback its useless) and CS only with other AZ also
Also only taking from other CCCam Servers is not my Interest.
It looks like whole AZHD, not ready, maybe later, not now, ask in Future.

hfmls
14-10-2009, 07:14 PM
no!

multicas is a cardsharing protocol too!

multicas can do this:
read your local;
read your local while u can connect to cccam clines;
use multicas PROTOCOL to cardshare (like mbox, cccam, multicas has his own protocol too) but at the moment multicas protocol can only connect to one user using server+client protocol.

u can use multicas instead to read local and connect to several cccam clines.

i for example have. local card reading + 4 cccam clines :)

hanswurscht
14-10-2009, 07:27 PM
no for which of my Text ;)

I know Multicas= can read local, its quite old, yes
So Multicas can only connect to Multicas in Server& Clientmode to one other Multicas User(this must be an AZHD because no other Receiver has this thing), correct?

If this is right its in client only Liner from CCcam?

4 cccam Lines, and they get what from you? nothing?
OK, this is no cardsharing, this is ...........dont find the right words for it because I wont blame anyone

I thought its a Tool like Mbox and real CCcam or gbox, but it isnt as far as I understand now.
So we cant compare this between a correct CS Tool

hfmls
14-10-2009, 07:30 PM
yes multicas is only server if using multicas protocol. and only for one peer.



it can connect to multiple clines but it canot share.


but do what we all do. mount a cccam server. then create a F: line to server your multicas :)

leerock
14-10-2009, 07:32 PM
ok i can now comfirm that they ve fixed the 2.1.2 problem....
not a single freeze in an hour....

very nice!!!!!!!!!!!

thanks opensat

hfmls
14-10-2009, 07:33 PM
yes, they did ;)

i forgot about mbox 0.4

mounted in half an hour a cccam server in dm7000, serving with F: line azbox hd multicas.

fast zapping, no freezes! :)

hanswurscht
14-10-2009, 07:48 PM
yes multicas is only server if using multicas protocol. and only for one peer.



it can connect to multiple clines but it canot share.


but do what we all do. mount a cccam server. then create a F: line to server your multicas :)


thx for explain, but this is not what I want to do.
Im tired about Server here and Server theere, here dyndns, there dyndns.

I will try to use one thing, no mix on two Boxes, here a Card, there a Card and I see that Mbox seems to be dead like a stinking fish.
No word from mower for Month, only a Board with "in next Weeks" and big blabla

Same with gbox, its only alive because there is a Mbox 0.4, otherwise gbox is also a dead stinking fish.

So only one with support is CCcam and no Way to make a stable Server with a real CCcam with recording working, without freeze on AZHD, with all Channel working, thats my bad.
So Im thinking about changing not the Server but the Receiver to Dreambox, I see no other Way at the Moment.

Im stuck for to look for new things going around and only half working, but I hope for all there will be better stuff for this Box.
All not very easy now

aqa
14-10-2009, 08:04 PM
when i put a nds local card in the slot cs stops working . why . any one else having same problems using multicas its a old blue card

Smudger
14-10-2009, 08:21 PM
yes mine stops workng for the packages that the card could open if enabled but if I move dish to another position then it opens those packages.

also still get annoying gliches/pauses ok if you watch football but when watching movies a little annoying.

rtificial
14-10-2009, 09:04 PM
I work with ~ 40 peers in 06


how many peers do u have in 06? 06 only works ok with 20 peers or less.

leerock
15-10-2009, 12:50 AM
yes mine stops workng for the packages that the card could open if enabled but if I move dish to another position then it opens those packages.

also still get annoying gliches/pauses ok if you watch football but when watching movies a little annoying.

Smudger.. it must be your server man....
i m connected to a very reliable pay server....
it s on a linux pc and it has only about 20 clients.....
it s the faster and reliable server i ever payed....

i ve been watching for about 6 hours now and didn't have a single glitch....
zapping is pretty fast too...

looks like multicas is going to be big!!!!!!!

too many improvements in just a few days


Finally we have an almost complete cccam client on this box....
and not half finished works....
i ve been waiting for such thing for about 7 months now :)

leerock
15-10-2009, 01:02 AM
tesdted it on many providers on hotbird and 16e.i get a lot of freezing on all channels only digitalb went great.nova dont open at all.with cccam 0.2 i dont have these problems.any suggestions?

well.....
nova works fine here......
everything is working fine.....
even ndz....
not a single freeze here....

i don t know if this really makes a difference but.....
delete splitterdata.bin....
reboot....
Edit your cccam.cfg with ultraedit..... (this may be important).....
and then load it....
so a new splitterdata.bin is created.....

and tell us how it goes

Smudger
15-10-2009, 07:39 AM
Also going to try this tip.

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@

Well deleted splitter.bn and recreated and restarted Multicas 1 hour and no freezes.

But noticed after a reboot server did not reconnect but after restart of cam it then connected ok.

Standby off and on no problems ony after reboot.

also if you reboot router or line drops have to restart cam no auto reconect.

Looks a good one.

Now I rate at 99.99999%

Thanks to all @ Opensat and to whever else worked on this.

:respect-067:

Carp95
15-10-2009, 08:49 AM
Now I rate at 99.99999%

Thanks to all @ Opensat and to whever else worked on this.

:respect-067:


@Smudger what the 0,00001% then??
Just curious

spinmar
15-10-2009, 08:56 AM
Well a small summary after the "s*y IT attack day".
It seems that it stopped all the card sharing in italy about s*y channels: after a first attack where scard (and then dreambox) are ok, the second attack in the evening stopped all emu, scard too.
People say that the next attack will be in the we (during seria A plays) e during champions league.
I think the problem is not only in italy because we are the first but after us problably sky uk, sky de, etc... will adopt the same method.
Well what to say: yesterday I think was a day we'll remember for long time :svengo::svengo:

Carp95
15-10-2009, 09:21 AM
Well they "changed" the lenght of ECM answers.
Therefore it isn't reqeunised by all softcams.

This trick will certainly be adopted by others, but shouldn't be that difficult to adjust

spinmar
15-10-2009, 09:37 AM
How can we report the s*y attack news to opensat (lenght ECM) which could solve the problem in next multicas release?

hfmls
15-10-2009, 09:45 AM
it«s just a matter of time..before this gets stable and then cccam and other emus come with updates

Carp95
15-10-2009, 09:53 AM
How can we report the s*y attack news to opensat (lenght ECM) which could solve the problem in next multicas release?

No need for, they know! ( Not only they but all other manufacteres off linuxreceiver wich act with softcam)

As hfmls says: updates will come, but I persenaly don't aspect them any sooner then full operational of the longer ECM.

Smudger
15-10-2009, 10:10 AM
@Smudger what the 0,00001% then??
Just curious

Nothing in the life is perfect. :respect-050:
If you say 100% people stop working. :respect-050:

to keep you happy ok now 100% cccam client :respect-059:

leerock
15-10-2009, 10:19 AM
@Smudger what the 0,00001% then??
Just curious

I guess that 0,00001% would be autoreconnect after connection loss,

and autostart after reboot(this may be a firmware problem?)

we are talking about a 100% cccam client though...

Not an emu for CS and all..
For those things i think we are at 70%
now :-)

tsakman
15-10-2009, 10:34 AM
While watching a tv channel press the
> >| key on your remote controller to appear the OpenXCAS EMU menu.
From there you can start and stop your installed EMU's.

hfmls
15-10-2009, 10:35 AM
I guess that 0,00001% would be autoreconnect after connection loss,

and autostart after reboot(this may be a firmware problem?)

we are talking about a 100% cccam client though...

Not an emu for CS and all..
For those things i think we are at 70%
now :-)

here, autostarts after reboot :)

sami8519
15-10-2009, 10:48 AM
you all talk about it as a complete project, yet Showtime Arabia on Nilesat, the package with all Premier league games Live does not open on all multicas versions. And it is not only showtime but all Irdeto ver 5.7 are not supported.

rtificial
15-10-2009, 10:55 AM
Ok, I have prepared myself for moving to multicas for trial.

I have moved my Mbox server and my NewCS to my CCcam server.

So I have a 2.1.2 CCcam server, with a local card in NewCS.

I also have my AZBox, with a local card as well.

Now, what I have to do is this: (right?)

- I will start all fresh with the 3501 FW
- Configure network settings, etc
- Restore my channel list
- Install latest Multicas via plugins menu ?
- Add a C-line in Multicas to my CCcam 2.1.2 server
- Adjust priocaid file

So, can anyone show me an example for C+ NL priocaid file?

What else should I change or do?

hfmls
15-10-2009, 11:11 AM
yes, that's it.

valerica
15-10-2009, 11:29 AM
It's not like this , 'cos there's a problem : multicas doesn't connect to 2.1.2 server ; u hv to downgrade it to 2.1.1 or a lower vers .
In priocaid.cfg just add 1 line 4 c+nl : 0100 .

Cheers ,
Val .

Smudger
15-10-2009, 11:37 AM
It's not like this , 'cos there's a problem : multicas doesn't connect to 2.1.2 server ; u hv to downgrade it to 2.1.1 or a lower vers .
In priocaid.cfg just add 1 line 4 c+nl : 0100 .

Cheers ,
Val .

Latest MultiCas now connecting to 2.1.2 Ok.

Carp95
15-10-2009, 11:46 AM
Now, what I have to do is this: YES!!
- I will start all fresh with the 3501 FW
- Configure network settings, etc
- Restore my channel list
- Install latest Multicas via plugins menu YES!!
- Add a C-line in Multicas to my CCcam 2.1.2 server
- Adjust priocaid file

So, can anyone show me an example for C+ NL priocaid file?

What else should I change or do?Reboot when finished HAHA


Just start with 0100 then the rest

Remember only room for 8 CAID

valerica
15-10-2009, 12:05 PM
Latest MultiCas now connecting to 2.1.2 Ok.

I hv version 1.60D-A02 and it doesn't conn. (red - checked with multicas-edit v1.2a) with 2.1.2 ; dvbapi/cc2.1.1 connects with this server . Is there any newer vers. than the above , pls ?

Cheers ,
Val .

tx0
15-10-2009, 12:05 PM
Just start with 0100 then the rest

Remember only room for 8 CAID

why it is limited?

Carp95
15-10-2009, 12:08 PM
why it is limited?


Don't know maybe there's something "hard"coded inside

leerock
15-10-2009, 12:30 PM
There never was a problem connecting to a 2.1.2 server....
It was connecting fine from the first (cccam client version)
But it had problems with freezes and such...
But now with the latest version it s working fine!!!
And yes that s the latest...
If your server has the "minimum client version" enabled then thats why you cant connect

rtificial
15-10-2009, 12:42 PM
What is exactly the latest version then?

I have just activated Multicas, connecting to my local CCcam 2.1.2 server, and it seems to work. I'm not sure whether it uses my CCcam network for channels not decrypted by my local card.

Also, I have my CCcam server connected to a local running NewCS server, serving another local card. I am not convinced it will first try this card before trying to decrypt 'externally'.

Maybe some more tweaking needs to be done.

goran
15-10-2009, 12:47 PM
Disconnect it all - apart from the one you wanna test, of course... No one will mind in that case... for an hour or so... ;)

rtificial
15-10-2009, 12:57 PM
Of course ;-) But I'll have to try and do some work in between as well :D

Carp95
15-10-2009, 01:28 PM
What is exactly the latest version then?

I have just activated Multicas, connecting to my local CCcam 2.1.2 server, and it seems to work. I'm not sure whether it uses my CCcam network for channels not decrypted by my local card.

Also, I have my CCcam server connected to a local running NewCS server, serving another local card. I am not convinced it will first try this card before trying to decrypt 'externally'.

Maybe some more tweaking needs to be done.

We can't check that for you but normaly CCcam will try the fasted route to ECM answer.
If your CCcam server finds the answer faster then your local card could answer it will choose the faster way.
You could alter the F line for multicas in your server setup and set that CAID to low level hop for instance C+ holland:

F: azbox multicas 3 0 0 { 0:0:1, 100:6A:1 )

Then multicas would only get hop1 cards voor 0100:00006A that means only your local card.

Same trick could be done with your newcs card:

First in server let the N line end on 256 ( after the deskey) now the newcs-card is shown as local in your CCcam server after that do the same trick with the F line for multicas (just add after the first one.
Lets say second one in newcs is german then:

F: azbox multicas 3 0 0 { 0:0:1, 100:6A:1, 1702:0:1 )


The above trick should work for all provider ID's

rtificial
15-10-2009, 02:28 PM
Right, I can try to work that out.

Already altered my N-line to have it seen as local.

I'll try the other options for some further testing. At this moment it is decoding using the card in NewCS by the way.

antrabe
15-10-2009, 05:24 PM
anyone gets install cccam 2.1.2 like server in our azbox?
its better mulicas with one cline connected to my own server than cccam 204 (dvbapicas)?

hfmls
15-10-2009, 05:26 PM
yes!

a lot better to use Multcas

antrabe
15-10-2009, 05:32 PM
yes!

a lot better to use Multcas

do you know wich files i have to replace in lib folder?

i use before all clines that we could insert in multicas and didnt works fine then you say i have to insert one fline in ccam.cfg in lib and only one cline in cccam.cfg in multicas folder. its ok

antrabe
15-10-2009, 06:04 PM
in this way i can get open anything.

leerock
15-10-2009, 06:24 PM
in this way i can get open anything.

if you want to use cccam as server and multicas as client on the same box...

although i don t understand why you want to do that...
you should...

delete dvbapicas_module.....

disable dvbapi and leave only multicas enabled

reboot

after the reboot start dvbapicas

wait a few seconds

and restart multicas

if your configuration is right it should work

antrabe
15-10-2009, 06:28 PM
delete dvbapicas_module.....could give 644 atributes its enough?disable dvbapi and leave only multicas enabled

reboot

after the reboot start dvbapicas here you want say multicas no?

wait a few seconds

and restart multicas

if your configuration is right it should work

its ok

Yoda
15-10-2009, 06:44 PM
Got to say amazing here guys, thanks to everyone involved.

Yoda

Smudger
15-10-2009, 07:01 PM
here, autostarts after reboot :)


Mine does now and connects to cccam server after putting 10 sec wait in conf file.

bcrazynutter
15-10-2009, 08:48 PM
Why is it only me that still has freezes on cccam with this latest multicas? Don't have any with native cccam, does anyone have any ideas? Cracking me up now this!!

rmt
16-10-2009, 08:27 AM
Why is it only me that still has freezes on cccam with this latest multicas? Don't have any with native cccam, does anyone have any ideas? Cracking me up now this!!

I have freezes too, with the latest version and no autostart

goran
16-10-2009, 10:20 AM
I don't know what you guys are on about.:smash: Delete all the .sh files and whatever else in terms of scripts you might have and just reboot the machine.;)

My Mbox, for instance, is starting with no mistake!!!!!!!!!!!!!:respect-054:

bcrazynutter
16-10-2009, 11:10 AM
I think I may have been having server troubles last night, seemed to be working fine this morning :respect-055:

rtificial
16-10-2009, 04:42 PM
Hmm, just got a phonecall from my wife that it is not opening any channels at the moment, and on my cccam server I can see the client is not connected. It also doesn't connect after restarting Multicas.

Am I missing some autoreconnect setting or something?

The cccam server is in the same wlan as the azbox...

kleinerjunge
16-10-2009, 06:13 PM
Autoreconnect works here without problems! Also no freezes until now, tested for about 1,5 hours. Not yet tested recording on SD/HD channels, will do it now!

cu
KJ

tsakman
16-10-2009, 06:27 PM
MultiCAS_v160D-B02-1_2k91015

Spain c..... ok


http://www.filesavr.com/multicasv160d-b02-12k91015

enrico001u
16-10-2009, 06:51 PM
MultiCAS_v160D-B02-1_2k91015



http://www.satpimps.co.uk/showthread.php?p=663466#post66346 6


uploaded to public uploads

thanks tsakman

sami8519
16-10-2009, 06:55 PM
as usual no changes log!!!

enrico001u
16-10-2009, 06:58 PM
Think people should be grateful of the updates rather than moaning to be honest

tsakman
16-10-2009, 07:00 PM
as usual no changes log!!!


Spain c..le is ok

sami8519
16-10-2009, 07:15 PM
Think people should be grateful of the updates rather than moaning to be honest

It is necessary and logical thing to reveal what is new in a new firmware or emu.

enrico001u
16-10-2009, 07:29 PM
1. tsakman did tell you what changed
2. who said opensat did not release a changelog?
just because it might not be posted on here it is possible that it still was released

icedemon
16-10-2009, 07:40 PM
**** Spain c..... ok

sami8519
16-10-2009, 08:04 PM
First, Taskman did not write changelog, he just said C spain is ok. I dont know if this coming from opensat or he just tried it and reported it.

Second, All previous versions of multicas did not contain a changelog, so it is naturally for me to think what taksman said is his experience not an opensat changelog!!!!

rtificial
18-10-2009, 09:39 AM
I've tried this now for a couple of days, but for me, it's definitely not as stable as Mbox.

I get scrambled messages on channels for which I have a local card in NewCS, in my own LAN, so that doesn't seem to be optimal. Other than that, I get scrambled when I turn on the AZBox, so I have to change a channel first. I get freezes here and there which I don't have in Mbox anymore.

I'm not convinced yet...

goran
18-10-2009, 10:19 AM
Yes, likewise.

More work needed... ;)

sami8519
18-10-2009, 10:20 AM
yeah, I also noticed many freezing during watching arsenal game, although it decodes from my local showtime card running on a CCcam server on a PC. and I also noticed that when my pc server has other clines beside my local cards,there is delay in opening the channels. Also when I have mutliple C lines in multicas, there is delay in opening the channels than when there is only one C line. But Nevertheless, for me it is a great step to add Iredeto 5.7 support, so I guess work is in porgress and next releases will hopefully be better.

medmed
18-10-2009, 11:01 AM
hi
many channels HD (can***** french) 19° not work , SD is ok .
can you fix this probleme please in the other realease ???

sami8519
18-10-2009, 11:25 AM
It seems there is a conflict between different encryption systems especially I noticed it between Irdeto and other encryption systems. For example I had Art Sports on nilesat open without problems, then I went to a channel with Cryptoworks encryption(Digiturk) and and it is open but when I went again to Art sports it never open whatever I do unless I restart the emu. This also happens between Irdeto and other encryption systems. Zapping between other systems is OK.It only crashes when I try to move to irdeto. It stops sending ECM on irdeto unless I begin with irdeto after restarting the multicas. I am connecting to a 2.1.2 CCcam server with 2 Clines in my multicas. Hope this helps.Thanks.

Yoda
18-10-2009, 11:28 AM
I've tried this now for a couple of days, but for me, it's definitely not as stable as Mbox.

I get scrambled messages on channels for which I have a local card in NewCS, in my own LAN, so that doesn't seem to be optimal. Other than that, I get scrambled when I turn on the AZBox, so I have to change a channel first. I get freezes here and there which I don't have in Mbox anymore.

I'm not convinced yet...

Same here, I reqally hope that these issues get resolved because the potential is amazing, some packages are perfect but my local white sly card just too many freezes.

Real shame.

Yoda

Smudger
18-10-2009, 01:49 PM
No one noticed new version in Plugin download?

1.60D-C01

medmed
18-10-2009, 01:52 PM
new multicas is avaible , 1.60D-C01

josepfdc
18-10-2009, 02:35 PM
I have just installed it but I haven't been able any difference yet between 1.60D-A

:-(

josepfdc

goran
18-10-2009, 04:07 PM
Telefonica [or some such package] fixed, that's all... ;)

kleinerjunge
18-10-2009, 04:11 PM
Hm,

for me seems to be more stable and a bit quicker. Recording also better. But still freezes from time to time when recording...

cu
KJ

hfmls
18-10-2009, 06:21 PM
dont use newcs+multicas in azbox hd.
because multicas is trying to access all the time to card reader (they should put an option to disable that)
and it creates freezes from local card

sami8519
18-10-2009, 07:09 PM
dont use newcs+multicas in azbox hd.
because multicas is trying to access all the time to card reader (they should put an option to disable that)
and it creates freezes from local card

but my local card was in a PC server running CCcam and in my azbox only multicas is installed.

marcinq76
19-10-2009, 11:24 PM
Hi,

for the forst time I found changelog for Multicas (not the latest version-but still a changelog) !

Thanks to colla!

MultiCAS_v160D_B02_1_2k91015

- CABLE SPAIN OK


fixes/improvements



- code cleanup

- improved S2 / S3 selection for CDS + TVV

- improved zap speed

- ecm.info+serverstats info in /tmp

- version info in /tmp

FENEKI
19-10-2009, 11:35 PM
hello mates how many server with can u put on AZBOX HD Elite with cccam because l hear there was only used to work with one server with 1 at the time.is it working like the dream box now with the lastes software.because l am asking u this because l would like to buy one.l went some of your mind
:respect-049:

aqa
20-10-2009, 12:10 AM
hello mates how many server with can u put on AZBOX HD Elite with cccam because l hear there was only used to work with one server with 1 at the time.is it working like the dream box now with the lastes software.because l am asking u this because l would like to buy one.l went some of your mind
:respect-049:

upto 32 with multicas

medmed
20-10-2009, 12:36 AM
for me CCcam natif it s work very good , but multicas (the latest ver.)
many freez in CCcam client .

kanber_kav
20-10-2009, 12:05 PM
MultiCAS share cardinfo file /tmp ?

kleinerjunge
20-10-2009, 12:21 PM
MultiCAS share cardinfo file /tmp ?

Yes, it is called "ccc_ecm.info" and is only generated when a channel is cleared by MultiCAS connecting to a CC******erver!

@medmed:
You have many freezes because MuliCAS doesn't handle ECM respones very good, or, in other words: When clearing a channel connecting to one server of one C-Line, MultiCAS stays on that server, independently from stability of this server! In those cases, another server is not asked for ECM response by MultiCAS!

cu
KJ

sami8519
20-10-2009, 12:52 PM
Hope this problem"sticking to the last server used" be solved in the next release. I am sure it will be, because people who did all this project cant be troubled by this relatively easy to correct problem.

happyhammer
20-10-2009, 01:36 PM
Hope this problem"sticking to the last server used" be solved in the next release. I am sure it will be, because people who did all this project cant be troubled by this relatively easy to correct problem.

is it really that easy? i wouldn't say so. How will you determine which server to use? if you have say 10 connected servers and a channel/package is available on all of them, how will it work out which one will give best service at that moment in time? a server may work well one day but not as good the next.

gtg60
20-10-2009, 02:52 PM
New version out:
MultiCAS_v160D-C02_2k91020

Cards viacces ok
stabylity satelittes-cable
fixed bugs cccam


Download here: http://www.satpimps.co.uk/attachment.php?attachmentid=38041&d=1256043095

hanswurscht
20-10-2009, 03:04 PM
it took about 20 Seconds to open a HD Channel, but then it works.
But changing back to mbox, without Server its not good for me.
anyway, nice to see that they are working on this Cam. Maybe it can be in Future a good one.

sami8519
20-10-2009, 03:55 PM
I find now that "the sticking to the last server problem" has been corrected. Anybody confirm guys? It was a very quick fix.......

antrabe
20-10-2009, 05:09 PM
yes i noticed that open kiquickliest good job. this is going better than cccam native

sami8519
20-10-2009, 06:09 PM
I have many freezings on my local Showtime card(irdeto2 ver 5.7).The card is in a CCcam server. Hope it is solved in the next release. Thanks.

kleinerjunge
20-10-2009, 06:36 PM
I find now that "the sticking to the last server problem" has been corrected. Anybody confirm guys? It was a very quick fix.......

This is not true!!

Still staying on first server, with which was cleared previous provider. After switching to my local provider (provider from local card) it stays still on the first one!

cu
KJ

medmed
20-10-2009, 07:17 PM
many freez in this ver .
natif CCcam work great

goran
20-10-2009, 07:27 PM
No, it doesn't! A bit of zapping and it's stuck!

Too many mediators/interceptors...

It's OK if you stay on a channel.

But zapping - kaput!

kleinerjunge
20-10-2009, 07:34 PM
Hi!

I have to say that the problem with staying on last used server is not solved, but this version works here really great! Much more stable with cards from distance 2 and 3!!!

cu
KJ

xanadu
20-10-2009, 09:52 PM
MultiCAS_v160D-C02_2k91020


This works perfect for me. :D :)

tx0
22-10-2009, 10:23 PM
I would like to say that MultiCAS_v160D-C02_2k91020 is completely rubbish with viacess as cccam client. have not noticed any changes from other 1.60 versions and cccam_module v0.2 seems to be more stable. Tested with latest fw 3501

Tarzan
22-10-2009, 10:58 PM
I would like to say that MultiCAS_v160D-C02_2k91020 is completely rubbish with viacess as cccam client. have not noticed any changes from other 1.60 versions and cccam_module v0.2 seems to be more stable. Tested with latest fw 3501

How did you install this version?

tx0
22-10-2009, 11:14 PM
@tarzan: as usuall. downloaded from OpenXCAS menu

pr2
23-10-2009, 06:23 PM
Hello,

First disable MultiCAS and then upgrade it from the internet. (Put a # in front of MultiCAS (blue button) and press the Yellow button to restart all camd (this will in fact stop all camd since no Camd is selected)).
If MutliCAS is still running I think he cannot replace the emu_module file so you version is not updated.

This version works fine on Viaccess channels no freeze, if you still have freeze you don't use the latest version.

Don't refer to the OpenXcas version indication, it is simply the one mentionned in openxcas.conf and this file can be replaced since it is not in used like emu_module.

Pr2

tx0
23-10-2009, 08:17 PM
Thanks for your attempt to help... I do know how to upgrade MutliCAS and FW. And I have the latest versions. I don't know may be it is the server issue cause its on the hop 2. Have no other server to test with.. But it freezes after few minutes and I'm getting "scrambled" message. ccc_ecm.info shows 'Not valid', but I'm not losing connection with the server. after a few minutes it happens again. The problem gets worse if you are trying to record something. I've made a little shell script for cron that prints ecm time on LCD and it seems to be ok... 0.19-1 sec... the average ping to the server is about 100ms.

#!/bin/sh
PATH=/bin:/usr/bin:/MMP/usr/bin
ECMTIME=`cat /tmp/ccc_ecm.info | grep 'ecm time' | awk '{print $4}'`
vfd_display -td210 $ECMTIME

hfmls
23-10-2009, 11:22 PM
where do we get it?

hfmls
24-10-2009, 12:27 AM
use rapidshare

gtg60
24-10-2009, 12:59 AM
There is a public upload section on this site:
http://www.satpimps.co.uk/forumdisplay.php?f=388

mushroom
24-10-2009, 09:25 AM
pls upload file here.as i read it has dre**ypt support in internal card reader.so platforma hd and penthouse hd will work
great step forward

mushroom
24-10-2009, 09:26 AM
here it is

скоро public MultiCas
Version 1.60D-D01
- Add: Support DRECrypt (Internal Cardreader) <----
- Fix: Problem NTV+ for CCcam client

Carp95
24-10-2009, 02:37 PM
1.60D-D01 Release date: 22/10/2009

- Add: Support DRECrypt (Internal Cardreader)
- Fix: Problem NTV + for CCcam client


also availeble through dbf plugin

tx0
24-10-2009, 03:19 PM
I would like to send special "thanks" for that Bulgarian squealer --> fenbg.
You asked why I've done this? Cause I think that such sw should be free
cause many people are not happy with azbox and because of such people
as you things get stuck. OK you are sitting there and keeping "secrets"... you know what? You remind me those dreambox- people that can do nothing but blame azbox.. I've got banned cause of you.. So what? go 2 hell..
I will post here whatever I like. cause I respect this forum and most people here. Now what I would like to add - the new fw is out. It keeped in secret yet. But should be out in a few days. Everyone will get it. some Sigma driver modifications. Will see.

antrabe
24-10-2009, 03:33 PM
have you the new firm?

tx0
24-10-2009, 05:11 PM
have you the new firm?


not yet mate. but opensat b-testers already have it. its up to opensat to release this fw for all. hope they'll do it asap. that could remove the gap bw
'privileged' b-testers and all ordinary users. We all in the same boat so its
not fair to make someone more 'privileged', right?

gtg60
24-10-2009, 06:10 PM
not yet mate. but opensat b-testers already have it.

Hmm, I know a beta tester and he doesn't have it yet, wonder what that's all about??

Have you any more info on this fw? Even the number??

tx0
24-10-2009, 07:14 PM
Have you any more info on this fw? Even the number??

Im not sure prob its v.3611

Carp95
24-10-2009, 08:14 PM
I would like to send special "thanks" for that Bulgarian squealer --> fenbg.
You asked why I've done this? Cause I think that such sw should be free
cause many people are not happy with azbox and because of such people
as you things get stuck. OK you are sitting there and keeping "secrets"... you know what? You remind me those dreambox- people that can do nothing but blame azbox.. I've got banned cause of you.. So what? go 2 hell..
I will post here whatever I like. cause I respect this forum and most people here. Now what I would like to add - the new fw is out. It keeped in secret yet. But should be out in a few days. Everyone will get it. some Sigma driver modifications. Will see.

Haven't got a clue what you're mumbling about???

No need for such a post?? just post files/images??

You're guessing m8:banghead:

crappy
24-10-2009, 09:44 PM
Damn right, ClosedSat told to many lies. Lets open cards or keep them closed. If you know something, share! (Sorry for my tone, just to dissapointed; don't take it personaly) :smilielol5:

kleinerjunge
24-10-2009, 11:53 PM
JSC Sports card (Al Jazeera) irdeto2 not cleared by Multicas as CCcam client. Getting "nok" from server. Can someone confirm?

In internal reader the card works!

cu
KJ

sami8519
25-10-2009, 06:55 AM
It is cleared perfectly for me.

medmed
25-10-2009, 07:15 AM
and for me , it's work

MrKappa
25-10-2009, 10:43 AM
Hello'
do you know about any activity to correct Multicas for Sly Italia?

mushroom
25-10-2009, 01:57 PM
Hello'
do you know about any activity to correct Multicas for Sly Italia?
this is not a simple issue to be solved by any emu atm i am afraid

kleinerjunge
25-10-2009, 03:22 PM
It is cleared perfectly for me.

and for me , it's work

Yes it's curious: The channels are cleared if a remote connection is used, and i mean always irdeto JSC Card!!
Only from my own card the channel is not cleared. Server is responding with "nok". Are there any differences in type of cards??

cu
KJ

sami8519
25-10-2009, 03:47 PM
Yes it's curious: The channels are cleared if a remote connection is used, and i mean always irdeto JSC Card!!
Only from my own card the channel is not cleared. Server is responding with "nok". Are there any differences in type of cards??

cu
KJ

I assume that your card has 0603 caid and not the 0604 caid which AFAIK is only used in Egypt. right?

kleinerjunge
25-10-2009, 03:53 PM
Yes, it is the 0603. And cleared channels from remote is also 0603!

cu
KJ

sami8519
25-10-2009, 04:16 PM
that's because your card 0603 needs update every half an hour or so. you must find somebody has DM to update your card for you throuh sending EMM for you.

goran
25-10-2009, 04:31 PM
MGcamd + NewCS -> Update...

Then... ;)

Tiptronic
25-10-2009, 08:18 PM
setup guides not necessary anymore I guess?

mushroom
25-10-2009, 09:22 PM
Multicas 160D-D05 available through dbf plugin
so far working fine on my azbox

tx0
25-10-2009, 09:27 PM
http://www.satpimps.co.uk/showthread.php?t=119223

medmed
25-10-2009, 10:01 PM
what's new in this version ?

tx0
25-10-2009, 10:29 PM
dunno. no info yet. guess they remove part of the code, y? dont like this 1

Yoda
25-10-2009, 10:49 PM
MultiCAS_v160-D05_2k91025.ZIP

Im using this and its a massive improvment, been using for half and hour on sly uk HD with card being shared from dreambox and its been perfect.

Well done and thanks guys.

hfmls
25-10-2009, 10:58 PM
thank you.

i wish they would allow how to check change log heheh

Smudger
25-10-2009, 11:05 PM
Have to agree this has to be the most stable yet for Sly NDS 28.2 watching SD for one hour and not one freeze.
Pixelation maybe twice but nothing I haven't seen on a sly box.

:bowing-036:

Well done guy's hope it's as good for other users.

hfmls
25-10-2009, 11:10 PM
:) cool

tx0
25-10-2009, 11:20 PM
may be I'm wrong and I'm using bad server. anyone can supply a better one?
::giggle::

kleinerjunge
25-10-2009, 11:35 PM
that's because your card 0603 needs update every half an hour or so. you must find somebody has DM to update your card for you throuh sending EMM for you.

Ok, this is not the problem, cause I have also DM600 here. I will observe that.

cu
KJ

Smudger
25-10-2009, 11:54 PM
Just monitored ECM times and they have been improved by half to what they were for me I used to get best .180 to .220 now it's .80 - .180.

hfmls
25-10-2009, 11:57 PM
wow! :)


hispasat zapping - 1.5 to 2 seconds :) conected to some friends
no freezes or pixelization

clines

icedemon
26-10-2009, 12:20 AM
I can't seem to connect to cccam server with new version, I've replaced the files in the folder with the ones in the zip, do I need to delete any other files?

EDIT
my bad, forgot to chmod

DOH

kleinerjunge
26-10-2009, 12:51 AM
I can't seem to connect to cccam server with new version, I've replaced the files in the folder with the ones in the zip, do I need to delete any other files?

Normally you have to delete splitterdata.bin and create a new one (with holding blue button on host line).

But I have to say that I have big problems with those new D-Versions (D01 and D05 now). They take long time to open channels even from local cards. Cards from distance are not cleared at all!!

Have to say that I dont trust those versions that are not on official download server...

cu
KJ

hfmls
26-10-2009, 01:13 AM
don't get me wrong..but that's probably bad configs...servers :S all is working good for us and for me.

kleinerjunge
26-10-2009, 01:16 AM
Just making fresh firmware flash and testing again!

cu
KJ

kleinerjunge
26-10-2009, 01:46 AM
Sorry but after firmware flash still big problems with D05! Some channels are not opened at all!

Back to C02 and all works fine.

But have to say that if channels are cleared with D05, it happens really fast!!

cu
KJ

irishchris
26-10-2009, 02:25 AM
auto selecting best peer in terms of ecm and quality looks to have been fixed compared to earlier versions where it would stay on the same peer with different packages regardless whether there was a better peer to connect to! good work guys!